Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Fort Worth, TX
Gate motor and opener problems in Fort Worth usually trace back to one of two causes: clay-soil post movement or heat-degraded internals on an older operator. We reset misaligned limits, replace failed capacitors and control boards, and retrofit openers onto gates that were never designed for automation. If your gate won’t move, moves halfway, or grinds when it runs, call (928) 260-0864 and a live person answers.
Why Fort Worth Homes Are Different
Fort Worth sits on Blackland Prairie clay, and that clay moves. After a wet spring, the soil under a gate post swells and lifts the post out of plumb. By August, the same clay shrinks and the post settles back, often an inch or more from where it started. The result is a gate that scrapes the ground, a hinge that binds, and a motor that overheats fighting a post it shouldn’t have to fight. We see this every year in Benbrook, Ridglea Hills, and the acreage tracts west of Loop 820.
The housing stock compounds it. Fort Worth’s west side (76126, 76116, 76132) holds a high concentration of ranchette properties with heavy pipe-rail gates originally hung for cattle, not convenience. Many weigh 400 pounds or more and were never counterweighted. When the summer heat past 100°F warps cedar boards and cooks the rubber seals inside an operator, the gate binds worse and the motor pulls harder. A technician who only knows ornamental driveway gates will misdiagnose half of what happens west of I-35W.
Our Main Fort Worth Services
Two services generate most of our Fort Worth calls: repair of an existing gate that has stopped working, and full installation of a new gate or a new automated system. Each has its own dedicated page.
Gate Repair in Fort Worth
Most repair calls in Fort Worth start with a gate that dragged for months before it finally stopped. Hinges seized, post leaned, motor cooked. We diagnose the full system rather than just replacing the part that failed, because on Blackland clay the real cause is usually below the hinge. Details are on the dedicated Gate Repair in Fort Worth page.
Gate Installation in Fort Worth
Installation in Fort Worth means accounting for clay movement from day one: deeper post footings, proper drainage around the post base, and operators sized for the gate’s actual weight. On the ranchette properties west of town, that often means automating an existing agricultural gate rather than hanging a new one. See Gate Installation in Fort Worth for what the work includes.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Motor & Opener in Fort Worth
Gate motor and opener work in Fort Worth is disproportionately repair-and-retrofit rather than replace-the-operator. The city’s western corridor is full of 1970s and 80s ranch gates that predate automation, along with newer suburban operators that fail early because the Blackland clay under the post has shifted the gate out of travel alignment. The result is a motor that stalls, strips a gear, or burns a limit switch long before the manufacturer’s rated lifespan. Our Gate Motor & Opener service covers swing and slide operators from nine brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule.
Motor Installation
Signs you need it
You are done opening a 400-pound pipe gate by hand, or your existing operator is dead and the repair estimate exceeds half the cost of a new unit sized correctly for the gate’s weight and post condition.
What it costs in Fort Worth
Motor installation in Fort Worth typically runs $1,400-$4,800 depending on gate weight, opener type, and whether the post or hinge work needs to happen first.
How we do it
We weigh the gate, check post plumb and soil condition, then mount and wire the operator and set the open and close limits with a written record of every value.
Motor Repair
Signs you need it
The gate opens halfway and reverses, grinds at the same point every cycle, or the motor hums but nothing moves.
What it costs in Fort Worth
Motor repair in Fort Worth typically runs $160-$850 depending on whether it is a limit-switch reset, a capacitor or gear, or a full control-board replacement.
How we do it
We pull the error codes first, then test the capacitor, gears, and limits in sequence, replacing only the failed part and photographing every reading before we close the cover.
Slide Motor
Signs you need it
Your slide gate jerks instead of glides, or the chain sags and the gate stops short of the open or closed receiver.
What it costs in Fort Worth
Slide-motor service in Fort Worth runs $780-$3,600 depending on chain drive versus rack drive, motor size, and whether the steel track needs straightening.
How we do it
We check the track for level over the span, set the chain tension, align the receiver, and adjust the motor’s torque and limit settings to match actual gate travel.
What Gate Motor & Opener Costs in Fort Worth
| Item | Typical range in Fort Worth |
|---|---|
| Capacitor replacement | $160 - $320 |
| Limit-switch adjustment / reset | $180 - $390 |
| Full motor or opener replacement | $1,400 - $4,800 |
Can you repair the motor on an old ranch gate that wasn’t built for automation?
Yes, retrofitting an operator onto an existing heavy pipe gate is a regular job in Fort Worth’s 76126 and 76116 zip codes. We verify post material, gate weight, and swing arc first, then recommend an opener rated for the load. Call (928) 260-0864 and we will price it in writing.
How fast can you get a Fort Worth gate motor running again?
Most motor repairs are same-day or next-day once we know the operator brand and the gate’s post condition. We carry common LiftMaster, BFT, FAAC, and Linear parts on the truck, which shortens the wait. Text a photo of the motor and we will tell you what we think it is before we dispatch.
Gate Access Control in Fort Worth
Gate access control in Fort Worth is less about securing a gated community and more about giving a single homeowner command of a long driveway that is invisible from the house. The ranchette lots west of the city and the newer builds north of Loop 820 both need reliable keypad or phone-based entry, because walking out to manually unlock a 400-pound gate every time a delivery arrives is not practical. Our Gate Access Control work covers keypads, remotes, phone entry, card readers, and video intercoms wired into the gate operator itself.
Keypad Entry
Signs you need it
You are changing a gate code by handing out the same one to every contractor, neighbor, and delivery driver and would rather issue individual codes you can revoke.
What it costs in Fort Worth
Keypad installation in Fort Worth runs $340-$1,900 depending on wired versus wireless, single versus multi-user, and whether the operator needs an interface board.
How we do it
We mount the keypad at reach height, wire or pair it to the opener’s control board, program the codes in front of you, and hand you a written cheat sheet for changing them later.
Phone Entry
Signs you need it
You want the gate to ring your cell phone instead of a buzzer in a house you are not standing in, or you need a visitor to call a number that opens the gate.
What it costs in Fort Worth
Phone-entry systems in Fort Worth run $690-$2,400 depending on cellular versus landline, number of stored contacts, and integration with existing access hardware.
How we do it
We connect a cellular gateway to your operator’s control board, program the forwarding number, and test the call-to-open path three times before we leave.
What Gate Access Control Costs in Fort Worth
| Item | Typical range in Fort Worth |
|---|---|
| Keypad installation | $340 - $1,900 |
| Phone entry system | $690 - $2,400 |
| Full access-control retrofit | $1,800 - $6,000 |
Will a Fort Worth heat wave affect my gate keypad or phone entry?
Heat kills outdoor electronics faster in Fort Worth than in most of the country. Keypads mounted in direct sun can delaminate and fail within a few summers. We mount them on shaded posts or specify units rated for continuous 120°F exposure. Call (928) 260-0864 to have us look at your current setup.
Can you add access control to a gate that has no motor yet?
Yes, and it is cheaper to plan the access control before the operator goes in. We run the keypad or phone-entry wiring during the motor installation rather than trenching twice. The written quote covers both parts, so there is no second invoice later.
Gate Parts & Welding in Fort Worth
Gate parts and welding in Fort Worth is not an occasional add-on; it is the core of most repair work on the city’s older pipe and tube gates. Hinges that have carried a sagging 400-pound gate for 30 years finally shear. Posts set in Blackland clay lean until the gate binds. Rails crack at the weld point where the gate was originally hung. Our Gate Parts & Welding service replaces what failed and reinforces what is about to.
Hinge Replacement
Signs you need it
The gate drags on the latch side, the hinge pin is worn flat, or the gate has already pulled a screw out of the post.
What it costs in Fort Worth
Hinge replacement in Fort Worth runs $180-$780 per hinge depending on gate weight, post material, and whether the post face needs repair before the new hinge mounts.
How we do it
We lift the gate off the post, cut or unbolt the old hinge, repair the mounting face, and weld or bolt a heavier-rated hinge in place with the gate re-hung level.
Post Replacement
Signs you need it
The post leans more than two degrees off plumb, the concrete collar around it is cracked, or the post is rusted through at the base where moisture collects.
What it costs in Fort Worth
Post replacement in Fort Worth runs $500-$2,500 per post depending on depth, concrete volume, soil condition, and whether the gate has to come off anchor first.
How we do it
We pull the old post, dig a deeper footing to reach past the clay movement zone, set the new post in concrete, and re-hang the gate after the pour has cured long enough to hold.
Custom Welding
Signs you need it
Your pipe gate has a cracked rail, a broken picket, or a hinge mount that was never properly gusseted and keeps tearing loose.
What it costs in Fort Worth
Custom welding in Fort Worth runs $95-$180 per hour plus materials, with most site welds for gate repair done in one to three hours.
How we do it
We clean the weld area, grind out the crack, weld it back with a gusset where the original design was weak, and photograph the finished bead before paint.
What Gate Parts & Welding Costs in Fort Worth
| Item | Typical range in Fort Worth |
|---|---|
| Hinge replacement | $180 - $780 per hinge |
| Post replacement | $500 - $2,500 per post |
| Custom welding | $95 - $180 per hour + materials |
Do you weld on-site in Fort Worth or take the gate to a shop?
We weld on-site with a mobile rig for almost every gate repair. Pulling a gate off its hinges and hauling it to a shop adds risk and time. The exception is restoration work best done on a bench. Call (928) 260-0864 and Adrian will tell you straight which way makes sense.
How long does a welded gate repair hold up in Texas weather?
Done right, a welded repair outlasts the original. We grind back to clean metal, use rod matched to the gate’s steel, and add gussets where the design was undersized. A photo of the finished weld goes in your file, so if it ever fails we can see exactly what was there.
Brands We Service in Fort Worth
We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule operators seen across Fort Worth homes and ranchettes. Common repair parts for our brands ride on the truck, which keeps most Fort Worth motor repairs to a single visit.
Pricing for Gate Repair in Fort Worth, TX
| Service | Typical range in Fort Worth |
|---|---|
| Gate & fence repair | $75 - $1,200 |
| Gate motor repair | $160 - $850 |
| Gate motor installation | $1,400 - $4,800 |
| Access control installation | $340 - $2,400 |
| Hinge replacement | $180 - $780 per hinge |
| Post replacement | $500 - $2,500 per post |
| Custom welding | $95 - $180 per hour + materials |
| Gate roller or wheel replacement | $120 - $1,000 |
| Full access-control retrofit | $1,800 - $6,000 |
Two things push Fort Worth prices above the national average: the clay soil, which means post and hinge labor on most calls, and the number of oversized ranch gates that need bigger operators and stronger hardware than a standard suburban driveway gate. Whatever the number, it is written down and handed to you before any tool comes off the truck.
Neighborhoods We Serve in Fort Worth
We run calls across Fort Worth’s full residential map, with most dispatch time between 45 and 90 minutes depending on traffic and where the crew is finishing the previous job.
- Benbrook and west Fort Worth ranchette tracts
- Ridglea Hills and Ridgmar
- Fairmount and Ryan Place
- North Fort Worth and Alliance corridor
- Southwest Fort Worth toward Aledo
Service Area - Cities Near Fort Worth
We also run calls in the cities that share Fort Worth’s western corridor soil and gate styles: Haltom City, TX, North Richland Hills, TX, Hurst, TX, and Bedford, TX. Dispatch is coordinated from the Dallas-Fort Worth office; the crews serve Fort Worth locally.
Serving Fort Worth, TX - Our Local Coverage Area
We’re based in the Fort Worth area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Fort Worth
Residential gate repairs on your own property do not require a permit in most of Fort Worth, but some neighborhoods with HOA covenants have their own aesthetic and construction rules, especially for front-facing driveway gates. We check the specific requirements for your street before any work starts. For access-control installations with new low-voltage wiring, we follow local code for buried cable depth and protection.
For a gate stuck open or stuck closed that leaves your property unsecured, we treat it as an emergency call. You will speak to a live person when you call (928) 260-0864, and we dispatch the nearest available technician rather than routing you through a callback queue. Most Fort Worth emergency calls get a same-day or next-morning visit.
We fix most of them. The steel in those old pipe gates is heavier than what most builders use today, and the failure is almost always at the hinge, the post, or the latch mount, not in the gate itself. We quote the repair honestly: if the gate is worth saving, we tell you, and the written price comes before any work begins.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Fort Worth Customers Say
"Good work on a long driveway gate. Arrived when they said, finished when they said."
- Sofia E."Honest about what did not need doing. Told me the operator had years left and only the control board needed replacing."
- Douglas N."Quoted in writing, installed on the day promised, and the price did not move. The crew was licensed and the number was on the paperwork."
- Wes A.