Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Keller
Gate installation in Keller, TX costs between $2,800 and $9,500 for most residential driveway gates, and between $1,200 and $3,800 for pedestrian gates. The larger figure on a swing or sliding driveway gate almost always comes down to the operator, the steel gauge, and whether HOA architectural approval requires a specific profile or finish. Our crews serve Keller neighborhoods including Hidden Lakes, Keller Crossing, and Marshall Ridge, and we carry a range of operators from Linear, BFT, Viking, and Ghost Controls so the new gate matches what the existing access system was built around. If you’re ready to get a written price before anyone turns a wrench, call us at (928) 260-0864.
Why Vance Gate Repair Is Keller’s Preferred Gate Installation Company
Keller homeowners call us because the quote comes in writing. That’s not a slogan for us. Under Haven Standard Clause 1, we hand over a written scope and a flat price before any material is cut or any post is set. The price on that sheet is the price on the final invoice, unless you change the scope after we start.
We also document the job. Every visit ends with a photo log showing what was found, what was set, and what was installed, including the part numbers. That matters in Keller more than most places, because many of these gates were installed by the same contractors during the 1990s and 2000s subdivision buildout. When a neighbor three doors down calls about the same failing Eagle operator you had replaced last year, we can pull your file and show them the exact failure mode, which saves everyone a service call.
Adrian Vance started this company in 2014 out of commercial access-control work, and that background shows up in the habits we carry into residential jobs: wiring diagrams, limit-switch readings, and a record you can hand to any future technician. Service is booked through our Dallas-Fort Worth office, with crews dispatched to Keller homes directly.
Our Gate Installation Services in Keller
Most Keller gate work falls into one of these four categories. Each of them has its own approval and soil considerations here, and we plan for those before we quote.
Driveway Gate Installation
Driveway gates in Keller are usually ornamental iron, often a single or dual swing leaf, set on brick pillars or steel posts at the entry to a large-lot home in an HOA community like Hidden Lakes. We handle the full installation: post setting, gate fabrication or pre-fabricated panel install, operator mounting, and the safety system. What we pay attention to that a generic installer won’t: the post footing depth relative to the clay soil. A 36-inch footing in stable soil might be fine elsewhere, but Keller’s shrink-swell soil wants a deeper set or a concrete collar, or that gate will be out of travel in two seasons.
Pedestrian Gate Installation
Pedestrian gates in Keller are typically built into the same ornamental iron fencing as the driveway entry, often with a maglock or keypad. Many of these were tied into the original access system installed at subdivision buildout, so the new gate has to match both the existing hardware and the HOA’s approved fixture finish. We stock common match profiles for the wrought-iron patterns seen across Keller Crossing and Marshall Ridge, and we can fabricate when a specific pattern has been discontinued.
Sliding Gate Installation
Sliding gates show up in Keller where lot geometry doesn’t leave swing clearance, or where the driveway opens directly onto a collector road like Keller Parkway or Bourland Road. The failure point in this market is almost always the bottom roller and the track pad. North Texas heat shifts the pad, the roller binds, the rack-and-pinion drive skips. We set slide-track pads with movement joints and grade the drain away from the track, which is the detail that keeps a sliding gate from binding in August.
Swing Gate Installation
Swing gates are the dominant installation type in Keller because the master-planned lots are wide enough to allow the leaf to travel inward. Dual swing is common on corner lots and on properties with a circular drive. We install single and dual swing gates with proper hinge placement, operator placement, and entrapment protection, and we re-set or reinforce existing posts where the clay has done its work. A new operator on a post that’s drifted 4 degrees out of plumb will fail early, so we measure the post before we ever quote the operator.
See more about the full range of work on our Gate Installation page, which covers the process from survey to final safety test.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterTrusted Brands We Service in Keller
We work on whatever automation is already on the property. In Keller, that’s often an original Linear or Eagle unit from the 1990s and 2000s that’s reaching the end of its life. We also install and service BFT, Viking, and Ghost Controls operators, and we keep common replacement parts stocked for fast turnaround on Keller jobs. If the existing operator can be repaired, we repair it and hand you the photo record with the part number. If it can’t, we explain exactly why and give you a written price for the replacement before you make any decision.
Common Gate Installation Problems We See in Keller Homes
These are the recurring issues we see on service calls and new installations across Keller. If you’re planning a new gate, knowing these now can save you a callback later.
- Black-clay soil heaving tilt gate posts. Keller’s shrink-swell clay expands and contracts through the wet-dry cycle, and over a decade or two that movement lifts and tilts the hinge post enough to bind the gate leaf mid-travel. The fix is a deeper post or a concrete collar, not just a hinge adjustment.
- Synchronized operator failures in 1990s and 2000s subdivisions. Hidden Lakes, Keller Crossing, and Marshall Ridge were built out in waves. The gates went in at the same time, with the same operators, and now they’re failing in clusters. We’ve replaced failing Eagle and Linear operators on the same street in the same season, which is a pattern specific to this city’s build-history.
- Heat-shifted concrete pads under sliding gates. Summer temperatures push and curl the pad, which binds the bottom rollers and skips the rack. We see this on sliding gates along wider lots off Rufe Snow and Johnson Road. The pad needs a movement joint and a drain path, or the track will bind every August.
- Photocell and safety-edge misalignment after post movement. When the post shifts, the gate’s travel path changes, and the safety photocell, the infrared beam that stops the gate if something crosses the path, gets knocked out of alignment. The operator then trips or refuses to close. We re-align and photograph the new position so you have a record of it.
Pricing for Gate Installation in Keller, TX
A pedestrian gate in Keller typically runs $1,200 to $3,800, depending on width, steel gauge, and whether the HOA requires a specific iron profile. A single swing driveway gate usually lands between $2,800 and $5,200, and a dual swing driveway gate with a new operator runs $4,500 to $9,500. Sliding gates fall in the $4,000 to $8,000 range because the track, pad, and rack add cost. Factors that move the price in Keller specifically: post depth corrections for clay soil, HOA-required finish work, and whether the existing operator is repairable or needs replacement.
| Installation Type | Typical Keller Price Range |
|---|---|
| Pedestrian gate | $1,200 - $3,800 |
| Single swing driveway gate | $2,800 - $5,200 |
| Dual swing driveway gate with operator | $4,500 - $9,500 |
| Sliding driveway gate | $4,000 - $8,000 |
Every quote is written. It includes the scope, the part numbers, the post-depth plan, and the operator choice. You agree to it before we order material. That’s Haven Standard Clause 1, and it’s the reason Keller homeowners who’ve been burned by verbal estimates call us. Call (928) 260-0864 for a free written estimate.
We Also Serve Cities Near Keller
From our DFW dispatch office, we cover Keller and the surrounding communities. That includes North Richland Hills, Southlake, Haltom City, and Colleyville. If you’re on the edge of Keller in a subdivision that straddles a city line, call and we’ll confirm the service area for your address.
Serving Keller, TX - Our Local Coverage Area
We’re based in the Keller area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Keller
Yes, in almost every Keller subdivision you do. The 1990s and 2000s master-planned communities here have architectural review committees that govern gate height, style, finish, and even the operator’s visible components. You’ll typically need to submit a drawing or photo of the proposed gate and a written description of the finish before work starts. We provide a spec sheet for your submission as part of the free estimate, because we’ve done this across Hidden Lakes, Keller Crossing, and Marshall Ridge, and we know what the committees look for. Call (928) 260-0864 and we’ll build the submittal with you.
The gates on a given street in Hidden Lakes were installed at roughly the same time, by the same contractor, using the same operator, during the subdivision’s buildout. Twenty to thirty years later, the wear hits all of them in the same window. We’ve replaced failing Eagle and Linear operators on the same block within the same season. If three neighbors on your street have replaced theirs, yours is likely next, and we can tell you from a single service visit whether the operator is repairable or near the end. Call (928) 260-0864 to have it checked before it fails.
The shrink-swell clay beneath Keller expands when wet and contracts when dry, and over seasons that movement can tilt a post or crack a footing. A new gate installation has to account for that in the post depth, the footing design, and the hinge geometry. We set posts deeper than the standard, use concrete collars where the soil is unstable, and grade the area so water moves away from the base. If the post moves, the gate binds and the operator trips the safety photocell, so getting the footing right is the most important part of a Keller installation.
Yes. Most Keller HOAs run one of a handful of access-control systems, usually a keypad or a card reader tied to a shared entry or a private driveway. We match the new operator to the existing system, including loop detectors, exit sensors, and the safety photocells, so the HOA’s entry keypad still talks to the gate the same way it always has. We’ve done this with Linear, Eagle, BFT, Viking, and Ghost Controls operators in Keller subdivisions, and we document the wiring before we touch anything. Call (928) 260-0864 and we’ll come survey the setup.
Yes. Automatic gate operators in Keller must meet the UL 325 entrapment protection standard, which means a working photo-eye, a reversing edge, or an equivalent safety system that stops and reverses the gate if something blocks the path. The same requirement applies whether it’s a new installation or an operator replacement on an existing gate. We test the entrapment protection after every installation and photograph the settings for your record. If your current gate closes against resistance without reversing, that’s a safety issue and it needs correction now.
Call us at (928) 260-0864. A live person answers, day or night, and the first visit ends with a written price in your hand, not a verbal guess. In Hidden Lakes, our crew replaced a failing Eagle swing gate operator on a brick-exterior home where the black-clay soil had heaved the hinge post enough to bind the gate mid-travel. We re-set the post footing, installed a LiftMaster operator with a loop detector, and re-aligned the safety photocells so the HOA-approved automatic gate opened smoothly for the resident’s keypad entry. We can do the same for yours.
Written by Adrian Vance, Owner at Vance Gate Repair, serving Keller and the DFW metro since 2014.