Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across North Richland Hills
Gate installation in North Richland Hills usually runs between $900 and $4,800 depending on the gate type, size, and whether we’re also setting new posts. Most single swing driveway gates land in the $1,400 to $2,600 range, while a full double gate with new footings and an opener can push past $4,000. We serve the entire city, from neighborhoods off Rufe Snow Drive to streets along Glenview Drive near Fossil Creek. Call (928) 260-0864 for a written price before any work starts.
Why Vance Gate Repair Is North Richland Hills’s Preferred Gate Installation Company
We’ve set gates throughout North Richland Hills long enough to know what the ground does here. The Vertisol clay under Tarrant County swells in wet springs and cracks in August heat, and that movement dictates how we pour footings and set posts. A gate installed in NRH without accounting for clay heave will lean within two seasons. We pour deeper than code minimums, tie rebar into the hinge posts, and photograph every step so you can see what’s under the ground before we backfill.
Every job carries a written scope and a flat price before we start, per Haven Standard Clause 1. When the crew leaves, you get a photo record of what was installed, the part numbers, and the limit and force settings on any opener. That documentation habit comes from Adrian Vance’s commercial access-control background starting in 2014, and it’s now standard on every residential gate we install in North Richland Hills. The 365-Day Done Right Promise covers the work: if something isn’t right within a year, we make it right at no charge.
We dispatch technicians to North Richland Hills daily. A live person answers the phone 24/7 at (928) 260-0864, and you’ll get the technician’s name and photo before arrival.
Our Gate Installation Services in North Richland Hills
Double Gate
Double driveway gates are the most common installation we handle in North Richland Hills. The city’s 1970s through 1990s subdivisions, like the streets north of Mid-Cities Boulevard and the neighborhoods behind the NRH Centre, were built with wide driveway entrances suited to two-leaf gates. We set both hinge posts in 30-inch footings with rebar cages, square the leaves to each other, and align the center catch so both sides close flush. Most double gate installations in NRH run $2,200 to $4,800, including the gate fabrication, posts, and hardware.
Driveway Gate
A single driveway gate in North Richland Hills typically costs $1,400 to $2,600 installed, depending on width and whether we’re automating it. Solid steel and composite frames hold up better here than cedar, which warps badly under the humidity-to-drought swings common in Tarrant County. We always ask about the driveway slope before quoting. Grading in NRH varies block to block, and a gate that must swing uphill needs a different hinge geometry than one on flat ground.
Sliding Gate
Sliding gates work well on North Richland Hills lots with short setbacks or steep driveway aprons where a swing gate would clip a car or a fence line. The tradeoff is track and roller maintenance, and in NRH the black clay shifts enough that a poorly compacted track bed will sag within a year. We run a compacted gravel base under the track and set the roller posts deeper than the gate posts. Expect $1,800 to $3,500 for a manual sliding gate installation in North Richland Hills, and more when we add automation.
Swing Gate
Swing gates remain the default choice across North Richland Hills because they match the brick ranch and traditional tract home aesthetic. We build them with steel frames and a finish of your choosing, then set the posts to account for clay expansion. A single swing gate without an opener typically runs $1,200 to $2,200 in NRH. When you add a motor, we set limit switches and force controls on site and hand you the written settings before we leave.
We’re the Gate Installation team that documents what we set. For North Richland Hills specifically, that means photos of the footing depth before concrete, a written record of the post spacing, and the opener brand and model noted on your invoice.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterTrusted Brands We Service in North Richland Hills
We install and automate gates using motors from BFT, Linear, Ghost Controls, and Viking, among others. If you already have an existing opener on the property, we’ll work with it rather than pushing a replacement unless the motor is genuinely done. Having local familiarity with multiple brands matters in North Richland Hills because so many homes here carry original 1990s-era openers that need a technician who knows the wiring and limit logic, not someone guessing. We stock common parts for those brands locally, which keeps most installations in NRH on a single-visit schedule.
Common Gate Installation Problems We See in North Richland Hills Homes
- Clay heave pushing hinge posts out of plumb. The Vertisol soil under North Richland Hills swells dramatically after wet springs and shrinks in summer heat. A post set at the standard 24-inch depth will lean within two seasons here, which is why we pour footings at 30 inches or more and tie the rebar cage directly into the post base.
- Storm runoff along Little Bear Creek and Fossil Creek bending gate frames. Low-lying streets near those drainage corridors see fast-moving debris during spring flash floods. We’ve pulled gate leaves that were lifted clean off their hinges and bent inward at the bottom rail. In those zones we recommend heavier steel frames and through-bolted hinges rather than lag screws.
- Cedar boards warping and checking within three to five years. The humidity-to-drought swing in North Richland Hills is brutal on wood. New installs in NRH increasingly use steel or composite frames so the gate doesn’t need board replacement every few years.
- Old cedar privacy fence gates hitting end-of-life all at once. North Richland Hills’s primary build-out happened between 1975 and 2000, so thousands of original board-on-board gates are now 25 to 45 years old. We often replace the post, frame, and gate as a unit rather than patching hardware onto a structure that’s already past its service life.
Pricing for Gate Installation in North Richland Hills, TX
Here are the ranges we see most often in NRH:
- Single swing driveway gate: $1,400 - $2,600 installed
- Double driveway gate: $2,200 - $4,800 installed
- Sliding gate (manual): $1,800 - $3,500 installed
- Pedestrian gate (steel frame): $700 - $1,500 installed
- Automation (motor, arms, photocells): $800 - $2,200 added to the gate price
What moves the number: gate width, whether we’re replacing the posts or setting new ones, the opener brand, and whether the driveway has a slope. Pool enclosure gates in North Richland Hills add cost because Texas code requires self-closing, self-latching, outward-opening hardware, which is more expensive than a standard latch set. The price you’re quoted is the price on the invoice. We hand it to you in writing before any work starts. Call (928) 260-0864 for an exact quote on your North Richland Hills property.
We Also Serve Cities Near North Richland Hills
Our crews cover North Richland Hills and the surrounding Tarrant County communities, including Hurst, Haltom City, Bedford, and Colleyville. If you’re a few blocks outside NRH city limits, call (928) 260-0864 and we’ll confirm coverage for your street before scheduling.
Serving North Richland Hills, TX - Our Local Coverage Area
We’re based in the North Richland Hills area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in North Richland Hills
Because the Vertisol clay under Tarrant County expands when saturated, pushing whatever’s set in it upward and outward. Post footings poured at shallow depths, typically the 24 inches many builders used in the 1980s and 1990s, get shoved out of plumb every wet season. We fix this by setting new posts in 30-inch footings with rebar cages tied to the post, which resists the expansion force far better. Call (928) 260-0864 and we’ll inspect your gate posts and give you a written price.
Locate the manual release mechanism, usually a small lever or pull cord on the operator unit, and pull it to disengage the motor from the gate. This lets the gate swing or slide manually until power returns. Don’t force the gate if it resists, because a bent rack or jammed roller can worsen under pressure. If you can’t find the release or the gate won’t move, call (928) 260-0864 and a technician will walk you through it or come out.
Yes. Texas pool barrier code requires gates around pools to be self-closing, self-latching, and to open outward away from the pool, with the latch positioned at a specific height. Many original pool gates in North Richland Hills were installed decades ago and don’t meet current code. When we install a pool enclosure gate in NRH, we set the hinges, closer, and latch to comply with current Texas requirements and document the settings. The cost for a compliant pool gate installation typically runs $900 to $1,800.
Low-lying streets along Little Bear Creek and the Fossil Creek drainage corridors channel fast storm runoff that carries debris, tree limbs, and loose fencing material. When that debris hits a gate, it can lift the leaf off its hinges or bend the bottom rail inward. This is a failure pattern we see routinely in those specific NRH neighborhoods and rarely in higher-elevation parts of the city. If your gate frame is bent, call (928) 260-0864 for a written repair or replacement quote.
Three to five years is typical for cedar boards in North Richland Hills, because the humidity-to-drought swing here is harsher than in most of Texas. The boards absorb moisture in spring, then give it up fast in 100°F summer heat, and that cycle checks and warps the wood. If you want a gate that doesn’t need board replacement every few years, we usually recommend steel or composite frames in NRH. A steel-frame double gate runs $2,800 to $4,800 installed, and the boards, if any are added as infill, are the only wood part you’d ever replace.
Get a Written Price for Gate Installation in North Richland Hills
We serve all of North Richland Hills, from the streets off Davis Boulevard to neighborhoods along Smithfield Road and everything in between. Every installation starts with a free assessment of your gate, posts, and the ground they sit in. You’ll get a written scope and a flat price before any tool is picked up, and a photo record when the job is done. Call (928) 260-0864 now to schedule your free estimate.
Written by Adrian Vance, Owner at Vance Gate Repair, serving North Richland Hills and the Dallas-Fort Worth metro since 2014.
Gate Installation in Nearby Areas