Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Plantation, FL
Gate motor and opener repair in Plantation usually starts with a dead operator on a 30-to-50-year-old HOA entrance, not a bent hinge or a snapped weld. The city’s master-planned subdivisions were built in a narrow window, which means entire communities now run on aging Linear, Eagle, and early LiftMaster units that fail within months of each other. If your gate won’t open, we diagnose the operator, the board, and the wiring before recommending anything. Call (928) 260-0864 and a live person answers, day or night.
Why Plantation Homes Are Different
Plantation was developed as one of Broward County’s first master-planned cities, and the result is an unusually dense concentration of HOA-governed subdivisions built mostly between the 1970s and early 1990s. Those communities feature ornamental aluminum and wrought-iron swing and slide gates at controlled entries, nearly all installed within a 1975 to 1995 construction window. When gate hardware ages out across an entire neighborhood simultaneously, you get clustered demand for full operator replacements rather than isolated one-off repairs.
The climate compounds the problem. Plantation sits near sea level within Broward County’s canal grid, including branches of the South New River and C-11 system. The water table is inches below grade, so underground conduit runs for loop detectors and low-voltage wiring flood routinely during the May to October wet season. Control boards and detector failures spike after heavy rain. Year-round humidity and intense UV also degrade capacitors and circuit boards well before their rated service life. Many 1980s-era communities still run obsolete Linear or Eagle operators with discontinued control boards, which means a technician either stocks legacy swap-out boards or defaults to a full operator replacement. Broward County’s post-Hurricane Andrew wind-load permitting requirements apply even to residential swing-gate replacements, and out-of-area contractors routinely miss that step.
Our Main Plantation Services
Plantation homeowners call us most often for two jobs: repairing an existing gate that has stopped working, and replacing a gate or full operator system that has reached the end of its service life. Both start the same way: a written price before any work begins.
Gate Repair in Plantation
Repair work in Plantation usually means a swing gate that won’t swing, a slide gate that binds on its rail, or an operator that hums but doesn’t move. We diagnose the mechanical and electrical fault, name the part, and price the fix in writing. Under Haven Standard Clause 4, every visit ends with a photo log of what was found and what was replaced. Gate Repair in Plantation covers the full scope of repair work we handle in this city.
Gate Installation in Plantation
Installation here means matching a new gate and operator to a community built decades ago, which usually involves wind-load compliance and HOA approval. We handle the full scope: gate fabrication, operator mounting, wiring, and the documented record the HOA expects. Gate Installation in Plantation explains the process and what a full installation includes.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Motor & Opener in Plantation
Gate motors and openers in Plantation fail in waves because the housing stock is so uniform. A Linear or early LiftMaster operator installed on a Plantation Acres or Jacaranda Lakes entrance in 1988 has now exceeded its design life by a decade, and the wet-season flooding of underground conduit only accelerates the control-board failures we see every summer. When we service a Gate Motor & Opener in Plantation, we check the operator, the limit switches, the photo-eyes, and the wiring path before we quote a replacement. The flat price is written and handed over before we pick up a tool, under Haven Standard Clause 1.
Motor Installation
Signs you need it
The operator hums but the gate won’t move, or the motor trips its breaker and the gate works only manually.
What it costs in Plantation
Motor installation in Plantation typically runs $650-$1,150 depending on brand, gate weight, and whether the arm bracket is intact.
How we do it
We remove the old operator, mount the new motor, set limit switches to the exact travel, align photo-eyes, and photograph the final wiring.
Motor Repair
Signs you need it
The gate moves slowly, reverses mid-cycle, or the operator clicks but fails to start.
What it costs in Plantation
Motor repair is priced after we identify the failed component, and most jobs land between $185 and $475.
How we do it
We test the capacitor, limit switches, and control board, replace the failed part, and reset travel limits to the manufacturer’s spec.
Linear Motor
Signs you need it
An older Linear operator on a 1980s-era HOA entry runs intermittently or has lost its programmed limits.
What it costs in Plantation
Linear motor replacement or repair in Plantation typically runs $475-$900 because legacy boards and arms are often involved.
How we do it
We identify the exact Linear model, source a compatible board or full replacement, and rewrite the limits and force settings before testing under load.
Slide Motor
Signs you need it
A slide gate stalls on its rail, grinds the chain, or the motor runs but the gate doesn’t travel its full length.
What it costs in Plantation
Slide motor service in Plantation starts around $550 and can reach $1,100 when the chain, sprocket, and rail brackets need replacement.
How we do it
We check the chain tension and sprocket wear, then repair or replace the slide motor and photograph the travel limits for the record.
Intercom Integration
Signs you need it
The gate motor works but the intercom won’t trigger it, or the entry system opens the gate but doesn’t ring the unit.
What it costs in Plantation
Intercom-to-motor integration in Plantation runs $220-$550 depending on whether we’re replacing a relay, a wire run, or a whole intercom board.
How we do it
We trace the wiring from the intercom to the operator, repair the relay or conductor, and test the call-to-open sequence several times.
What Gate Motor & Opener Costs in Plantation
| Item | Typical range in Plantation |
|---|---|
| Motor repair (component-level) | $185-$475 |
| Linear motor replacement | $475-$900 |
| Slide motor service | $550-$1,100 |
How fast can you fix a gate motor in Plantation?
Most motor repairs and replacements happen the same day we arrive. Linear and legacy Eagle units sometimes need a board sourced from our stock, which adds a day. The price is written before we start, no surprises.
Do you service the old Linear operators on Plantation HOA gates?
Yes. We stock legacy Linear boards and arms for the 1980s-era operators still running across Plantation’s subdivisions. When a board is truly discontinued, we quote a full replacement and put the number in writing before any work. Call (928) 260-0864 for an exact quote.
Gate Access Control in Plantation
Access control in Plantation means retrofitting entry systems onto gates built before modern keypads and phone-entry existed. The 1980s communities here run on telephone entry and basic keypads that weren’t designed for the humidity and lightning activity Broward County gets every wet season. When we service Gate Access Control in Plantation, we replace or repair the entry device, the relay wiring, and the power supply, then photograph the completed wiring so the next technician doesn’t have to guess.
Keypad Entry
Signs you need it
The keypad won’t accept codes, works intermittently, or a code opens the gate for every resident instead of the one who entered it.
What it costs in Plantation
Keypad replacement or repair in Plantation runs $185-$450 including weather-sealing and programming.
How we do it
We replace the keypad or its wiring, reprogram the codes, and test the relay output to the operator before sealing the housing.
Phone Entry
Signs you need it
The call box won’t dial out, calls drop before the gate opens, or the entry system works for some residents but not others.
What it costs in Plantation
Phone entry repair in Plantation typically runs $275-$625 depending on whether the problem is the phone board, the relay, or the phone line itself.
How we do it
We test the phone line, the call box board, and the relay to the operator, then replace the failed component and verify a call-to-open sequence on site.
Video Intercom
Signs you need it
The video feed is blank, the intercom audio is distorted, or the unit won’t release the gate when a resident answers.
What it costs in Plantation
Video intercom installation or repair in Plantation runs $450-$1,200 depending on whether we’re adding a camera, a monitor, or replacing a failed unit.
How we do it
We mount the camera or monitor, run the low-voltage wiring, pair the unit with the operator relay, and photograph the final installation.
What Gate Access Control Costs in Plantation
| Item | Typical range in Plantation |
|---|---|
| Keypad entry repair | $185-$450 |
| Phone entry repair | $275-$625 |
| Video intercom installation | $450-$1,200 |
Can you upgrade a 1980s Plantation entry system without replacing the gate?
Yes. We retrofit new keypads, phone entry, or video intercoms onto the existing gate and operator. The wiring run gets documented and photographed, and the price is written before we start. Call (928) 260-0864 for a quote.
Does Plantation HOA work require board approval before access control work?
Most Plantation HOAs require written approval before any gate or entry system work begins. We provide the scope and price in writing, which most boards accept as the proposal document. The estimate is free and the price doesn’t change after approval.
Gate Parts & Welding in Plantation
Gate parts and welding in Plantation usually means a wrought-iron swing gate that has sagged on its hinges after decades of daily use, or an aluminum slide gate that binds because its rollers wore flat. The planned-era masonry communities here used ornamental metal gates almost exclusively, and the salt-heavy humidity accelerates rust at hinge welds and bracket points. When we handle Gate Parts & Welding in Plantation, we repair or replace the worn component, weld where needed, and photograph every part before and after the work, as Haven Standard Clause 4 requires.
Hinge Replacement
Signs you need it
The gate drags on the ground, the hinge pins show visible wear, or the gate won’t close squarely against the latch.
What it costs in Plantation
Hinge replacement in Plantation runs $185-$475 per hinge depending on gate weight and whether new weld plates are needed.
How we do it
We support the gate, cut or unbolt the old hinge, weld or bolt the replacement, and re-level the gate before photographing the work.
Rail Repair
Signs you need it
A slide gate jumps its rail, scrapes along the ground, or the rail shows deep wear grooves in the wheel path.
What it costs in Plantation
Rail repair or replacement in Plantation runs $450-$1,100 depending on rail length, material, and whether the gate must be re-hung.
How we do it
We measure the existing rail, remove the worn section, weld or bolt the replacement, and test the gate’s travel under load.
Gate Rollers
Signs you need it
The gate shudders as it moves, the rollers show flat spots, or the gate sits low on one end of its travel.
What it costs in Plantation
Gate roller replacement in Plantation runs $250-$650 depending on the number of rollers and whether the rail also needs attention.
How we do it
We replace the worn rollers, clean and lubricate the rail, adjust the gate’s level, and photograph the final alignment.
Custom Welding
Signs you need it
A picket has broken away from the frame, a hinge plate has cracked, or the gate needs a modification the original fabrication didn’t include.
What it costs in Plantation
Custom welding in Plantation is quoted per repair after we see the break, and most jobs land between $150 and $600.
How we do it
We clean the weld area, weld the repair with the correct rod or wire for the metal, grind and finish the joint, and photograph it.
What Gate Parts & Welding Costs in Plantation
| Item | Typical range in Plantation |
|---|---|
| Hinge replacement | $185-$475 per hinge |
| Rail repair | $450-$1,100 |
| Gate roller replacement | $250-$650 |
Can you weld a sagging Plantation swing gate in place, or does it need to come down?
Most sagging gates can be welded in place after we support the leaf and re-level it. We match the welding process to the metal, and you get a photo of the finished weld before we leave. Call (928) 260-0864 for a quote.
Do you replace parts on ornamental aluminum gates common in Plantation?
Yes. We replace hinges, rollers, brackets, and pickets on the ornamental aluminum and wrought-iron gates found across Plantation’s HOA communities. Parts are matched to the existing profile, and the price is written before work begins.
Brands We Service in Plantation
We work on whatever motor is already on your Plantation gate. Our technicians carry parts for Linear, BFT, and Viking operators, plus Legacy Eagle boards for the older HOA systems across the city. We don’t steer you toward a replacement when a repair makes sense. See our brands for the full list of what we service.
Pricing for Gate Repair in Plantation, FL
| Service | Typical range in Plantation |
|---|---|
| Motor repair (component-level) | $185-$475 |
| Linear motor replacement | $475-$900 |
| Slide motor service | $550-$1,100 |
| Keypad entry repair | $185-$450 |
| Phone entry repair | $275-$625 |
| Video intercom installation | $450-$1,200 |
| Hinge replacement | $185-$475 per hinge |
| Rail repair | $450-$1,100 |
| Gate roller replacement | $250-$650 |
| Custom welding | $150-$600 |
Wet-season flooding of underground conduit pushes access control and motor prices toward the upper end when we have to pull and replace wiring, and legacy Linear or Eagle boards cost more because the stock is finite. Every Plantation job gets a written price before work starts, and that price doesn’t change at the end of the visit.
Neighborhoods We Serve in Plantation
We work across Plantation’s residential communities, from the canal-side streets along the C-11 system to the planned subdivisions east of University Drive. Response time for most Plantation visits is under 90 minutes for emergency motor failures, and we schedule installations and welding on a written-scope basis.
- Plantation Acres
- Jacaranda Lakes
- Fountain Springs
- Lago Mar
- Plantation Isles
Service Area - Cities Near Plantation
For gate work just outside Plantation, our technicians also cover Fort Lauderdale, FL, Margate, FL, Coconut Creek, FL, and Pompano Beach, FL. Dispatch and scheduling are coordinated from our South Florida office, and crews serve Plantation locally.
Serving Plantation, FL - Our Local Coverage Area
We’re based in the Plantation area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Plantation
We dispatch to most Plantation neighborhoods within 90 minutes for a dead gate or a stuck operator. A live person answers the phone 24 hours a day, so you’ll speak to a human, not a voicemail queue, when you call (928) 260-0864.
Most HOA communities in Plantation require written board approval before major gate or operator work begins. We provide the written scope and price that most boards accept as the proposal document, and we flag any Broward County wind-load permitting requirement before work starts.
Yes. Under Haven Standard Clause 1, every job starts with a written scope and a written price, which is what most Plantation HOAs and property managers request anyway. The estimate is free, and you can call (928) 260-0864 to schedule one.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Plantation Customers Say
"They installed the opener and left me a diagram of the wiring and the limit settings. When I needed a second remote programmed I could do it myself."
- Nadine C."The safety loop had never been installed correctly by the previous company. They showed me the reading, fixed it, and did not charge me for the diagnosis."
- Patrick H."Our gate was hit by a delivery truck. They came out, documented the damage properly for the insurer, and the claim went through without an argument."
- Camille R.