Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Gate Repair in East Naples, FL
Gate motor and opener failure in East Naples most often comes down to two things: operators installed in the 1980s and 1990s that have finally worn out, and summer lightning working its way into control boards. We replace, repair, and maintain swing and slide gate motors across the Radio Road and Rattlesnake Hammock Road corridors every week. If your gate is stuck open, stuck closed, or only moves halfway before reversing, call (928) 260-0864 and we’ll tell you exactly what we charge before anyone drives out.
Why East Naples Homes Are Different
East Naples is where Collier County concentrated its HOA-gated communities during the 1980s and 1990s boom. Neighborhoods like Falling Waters, Lely Golf Estates, and Riviera Golf Estates were built with entry gates installed at the same time as the first phase of homes, which means the operators, loop detectors, and keypads are now 25 to 35 years old and failing together. We regularly find obsolete loop detector wiring and corroded 24V control boards that were obsolete before the manufacturer discontinued them.
The climate does not help. East Naples sits slightly inland but still gets intense subtropical UV, near-daily summer thunderstorms, and humidity that pushes moisture into motor housings and oxidizes circuit boards. Lightning strikes on entry monuments are a recurring cause of control board failure across the area. And after Hurricane Irma in 2017, Collier County tightened permitting reviews for gate replacements in flood-zone communities. A gate operator swap along low-lying corridors near Rookery Bay without the correct permit risks a stop-work order and forced removal. We pull the permit before the first tool comes off the truck.
Our Main East Naples Services
Most East Naples homeowners call us for one of two reasons: their existing gate has stopped working, or they have finally decided the old gate is not worth repairing again. Here is what each involves locally.
Gate Repair in East Naples
Repair work in East Naples usually means diagnosing a gate that opens when it should not, stalls on the rail, or trips the breaker without moving. The housing stock here is mostly 1980s to 2000s stucco-over-block with ornamental aluminum or wrought-iron perimeter fencing, and the gate hardware has typically been in place since the original build. We find rusted hinge shoulders, sagged weld joints, and actuators that have never been serviced. Every repair starts with a written price and ends with a photo log of what we changed. See Gate Repair in East Naples for the full scope of what we handle on existing gates.

Gate Installation in East Naples
New gate installation in East Naples often means replacing an HOA-era gate that no longer meets current wind-load or safety codes. We handle the full job: removing the old gate and operator, setting new posts in concrete, hanging the gate, mounting the motor, and wiring safety edges and photo-eyes. In flood-zone communities near Rookery Bay, the permitting path matters as much as the metalwork. We walk every installation through the county review before we start. See Gate Installation in East Naples for how we build a new gate from the ground up.

What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Before
AfterGate Motor & Opener in East Naples


Gate motor and opener work in East Naples is dominated by operators that date back to the original HOA development of the 1980s and 1990s. Those motors have run their service life, and the humidity plus summer lightning here means the failure is usually in the control board or the limit switch assembly rather than the mechanical drive. We service nine automation brands, including Viking, Ghost Controls, and DoorKing, and we never steer you toward replacing a motor that can be repaired for less. Our Gate Motor & Opener service covers everything from a single capacitor replacement to a full swing or slide operator swap, all priced in writing before we start.
Motor Installation
Signs you need it
The motor hums but the gate does not move, or the gate stalls repeatedly and trips its breaker under normal load.
What it costs in East Naples
Motor installation in East Naples generally runs $450 to $1,400 depending on whether we are reusing existing brackets, replacing the arm assembly, or installing a new operator on a gate that already has conduit and power.
How we do it
We disconnect the old operator, photograph the existing wiring before touching anything, mount the new motor, set the torque and limit switches, and run a full open-close cycle while measuring the current draw.
Linear Motor
Signs you need it
The gate moves in jerks or has lost its smooth travel, often because the linear arm or screw drive has worn to the point of binding.
What it costs in East Naples
Linear motor replacement in East Naples typically falls between $500 and $1,200, with the final number driven by whether the existing bracket and pin are still sound.
How we do it
We remove the old linear arm, check the gate leaf for sag that would strain any new motor, set the new arm on the original mounting points, and dial in the travel stroke with the limit reading photographed.
Slide Motor
Signs you need it
The gate shudders as it travels, the chain or belt slips on the drive sprocket, or the motor trips its internal thermal overload on hot days.
What it costs in East Naples
Slide motor work here usually runs $550 to $1,500 depending on whether it is a straight motor swap or the drive chain, sprocket, and tensioner need replacement at the same time.
How we do it
We check the rail and roller alignment first, because a new motor on a misaligned rail fails the same way, then swap the operator and set the speed ramp so the gate does not slam at either end of travel.
What Gate Motor & Opener Costs in East Naples
| Item | Typical range in East Naples |
|---|---|
| Motor installation | $450 - $1,400 |
| Linear motor | $500 - $1,200 |
| Slide motor | $550 - $1,500 |
Can you fix a gate motor the same day in East Naples?
Yes. Most single-motor repairs in East Naples are completed the same visit. We carry common control boards, capacitors, and limit switches on the truck, and a stock of operators from brands like Elite and DoorKing. Call (928) 260-0864 and we will confirm availability before you commit.
How much does a gate opener replacement cost in East Naples?
A full gate opener replacement in East Naples runs between $450 and $1,500 depending on the drive type, brand, and whether the existing arm bracket is reusable. The price is quoted and agreed in writing before any work starts. Call (928) 260-0864 for an exact quote.
Gate Access Control in East Naples


Access control in East Naples is where HOA-era systems show their age fastest. Many communities still run keypads and phone-entry systems installed in the 1990s, and manufacturers discontinued those parts years ago. The near-daily summer storms also mean telephone entry boxes take water at the top seams and fail silently, so we test every component, not just the one that was reported dead. Our Gate Access Control work covers keypads, remotes, phone entry, card readers, and video intercoms, priced in writing before we open the box.
Keypad Entry
Signs you need it
The keypad accepts some codes but not others, or the buttons stick from sun and weather exposure and stop registering presses.
What it costs in East Naples
Keypad replacement in East Naples typically runs $175 to $450 depending on whether we are swapping a single-gang surface-mount unit or a pedestal keypad tied to a legacy board.
How we do it
We identify the exact model and its outputs first, then replace the keypad and reprogram all resident codes, photographing the new unit and its wiring before we seal the housing.
Phone Entry
Signs you need it
Callers buzz the pedestal and it rings but the gate release never fires, or the display has gone blank after a rain event.
What it costs in East Naples
Phone entry repair or replacement in East Naples usually runs $200 to $550, with fully new cellular-ready systems at the higher end of that range.
How we do it
We test the phone line or cellular signal at the pedestal, check the relay output that fires the gate, and replace the board or the entire pedestal unit as needed, then photograph the new wiring configuration.
What Gate Access Control Costs in East Naples
| Item | Typical range in East Naples |
|---|---|
| Keypad entry | $175 - $450 |
| Phone entry | $200 - $550 |
| Remote control programming | $75 - $200 |
Will a new access control system work with my existing gate motor?
Yes, in most cases. We wire new keypads, phone entry, and card readers to the existing operator controls as long as the motor’s input terminals are intact. We document every connection so a future technician does not trace the same wires twice. Call (928) 260-0864 to walk through what works with your existing setup.
How much does it cost to add a keypad to a gate in East Naples?
Adding or replacing a keypad in East Naples runs about $175 to $450 including programming. The written quote covers the part, the labor, and the code setup before we start. Call (928) 260-0864 for a precise number on your existing gate.
Gate Parts & Welding in East Naples


Parts and welding in East Naples come down to metal fatigue and rust. The ornamental aluminum and wrought-iron gates installed in the 1980s and 1990s have hinge shoulders that wear egg-shaped, post bases that corrode from high humidity, and weld joints that have been flexing for thirty years. The alkali in Collier County’s groundwater accelerates rust on ferrous hardware even for properties not on saltwater. Our Gate Parts & Welding service replaces worn hardware and re-welds cracked joints in place, so you do not pay for a new gate when the old one has another fifteen years in it.
Hinge Replacement
Signs you need it
The gate drags at the latch line, the hinge pins have visible vertical play, or the leaf sags enough that the gate binds before it closes.
What it costs in East Naples
Hinge replacement in East Naples typically runs $120 to $500 per hinge assembly depending on gate weight, access, and whether we are cutting out welded hinges or unbolting weld-on replacements.
How we do it
We support the gate leaf, cut or unbolt the worn hinge, square the gate in the opening, and weld or bolt the new hinge in place, then photograph the finished weld and the gate’s final closed position.
Post Replacement
Signs you need it
The post is peeling at the base, the gate post leans into the opening, or water has pooled around the footing and the post no longer holds the gate square.
What it costs in East Naples
Post replacement in East Naples usually runs $350 to $1,100 per post, driven by whether the old post is concreted deep, the site has access for a concrete saw, and whether the adjacent fence section needs temporary support.
How we do it
We cut the old post at grade, dig or jackhammer the footing, set a new post in concrete, brace it square, and re-hang the gate after the concrete reaches initial set, documenting every step with photos.
What Gate Parts & Welding Costs in East Naples
| Item | Typical range in East Naples |
|---|---|
| Hinge replacement | $120 - $500 per hinge |
| Post replacement | $350 - $1,100 per post |
| Rail repair | $100 - $400 |
Can you weld an aluminum gate in place in East Naples?
Yes. We weld ornamental aluminum and wrought-iron gate frames in place most weeks, usually for cracked hinge points or broken scrollwork. The gate does not need to come off its hinges for most in-place welds. Call (928) 260-0864 and we will tell you whether yours is weldable based on photos.
How much does a gate hinge replacement cost in East Naples?
Hinge replacement in East Naples generally lands between $120 and $500 per hinge. The spread depends on gate weight and whether the old hinge is bolted or welded. We quote the full number in writing before cutting begins, and call (928) 260-0864 gets that number fast.
Brands We Service in East Naples

We service Viking, Ghost Controls, DoorKing, and Elite operators throughout East Naples, plus five other major automation brands. We stock common control boards, remotes, and limit switch assemblies on the truck so most motor work does not wait on a parts order. See our brands for the full list.
Pricing for Gate Repair in East Naples, FL
| Service | Typical range in East Naples |
|---|---|
| Motor installation | $450 - $1,400 |
| Linear motor | $500 - $1,200 |
| Slide motor | $550 - $1,500 |
| Keypad entry | $175 - $450 |
| Phone entry | $200 - $550 |
| Remote control programming | $75 - $200 |
| Hinge replacement | $120 - $500 per hinge |
| Post replacement | $350 - $1,100 per post |
| Rail repair | $100 - $400 |
What pushes a price toward the top of these ranges in East Naples is usually the age of the original installation: obsolete wiring, rotted post bases, and HOA permitting requirements all add scope. What does not change is our upfront pricing. The written price you get before we start is the price you pay after we leave, under Clause 1 of The Haven Standard.
Neighborhoods We Serve in East Naples

We cover all of East Naples, from the gated communities along Radio Road and Rattlesnake Hammock Road to the smaller HOA enclaves farther east. Our technicians carry the full parts load for common motor and access control repairs, so most calls are handled on the first visit.
- Falling Waters
- Lely Golf Estates
- Riviera Golf Estates
- Briarwood
- Indigo Lakes
Service Area - Cities Near East Naples
Our East Naples crews also cover surrounding Southwest Florida communities when schedules allow. If you are in Jacksonville, FL, Miami, FL, Tampa, FL, or Orlando, FL, call (928) 260-0864 and we will route your call to the nearest available technician.
Serving East Naples, FL - Our Local Coverage Area

We’re based in the East Naples area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in East Naples
Most East Naples repair calls are answered by a live person 24 hours a day, and we dispatch technicians to the Radio Road and Rattlesnake Hammock Road corridors the same day for motor and opener failures. We confirm the arrival window when you call, and you get the technician’s name and photo before they show up.
Yes. Collier County enforces stricter permitting reviews for gate replacements in flood-zone communities, and we handle the permit application and county review before any work starts. We pull the correct permit for the job, not a shortcut that risks a stop-work order. Call (928) 260-0864 to check your specific property.
Yes, we work inside gated communities throughout East Naples, including Falling Waters, Lely Golf Estates, and Riviera Golf Estates. We coordinate with HOA boards and property managers when entry access or common-area gates are involved, and we provide the photo documentation most boards require after the work is done.
If your gate is stuck, grinding, or dead in East Naples, call (928) 260-0864 now. We answer live, we quote in writing before any work begins, and we leave you with a documented photo record of what we found and what we fixed. That is the only way we work, and it is what every East Naples gate job gets.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What East Naples Customers Say
"Good work on a long driveway gate. Arrived when they said, finished when they said."
- Sofia E."Honest about what did not need doing. Told me the operator had years left and only the control board needed replacing."
- Douglas N."Quoted in writing, installed on the day promised, and the price did not move. The crew was licensed and the number was on the paperwork."
- Wes A.





Before
After
Before
After