Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Beverly Hills, CA
Gate motor and opener repair in Beverly Hills usually means working on a heavy custom iron or steel gate paired with a European-brand operator like FAAC or BFT, often on a hillside lot in Trousdale or the flats south of Santa Monica Blvd. Most calls we get involve motors that stopped mid-travel, sensors tripped by Santa Ana winds, or operators that were never properly permitted when they were installed. The written price comes before any work starts, and a live person answers at (928) 260-0864 any hour.
Why Beverly Hills Homes Are Different
Beverly Hills is its own municipality with its own building and permit department, entirely separate from LADBS. Any gate operator installation, electrical upgrade, or structural modification here requires city permits and inspections that contractors working mostly in Los Angeles are often unprepared to handle. That matters on nearly every job we take in this city.
The housing stock splits between grand Spanish Colonial, Tudor Revival, and Mediterranean estates in the flats and the Mid-Century Modern showplaces of Trousdale Estates on hillside lots north of Sunset. Virtually every property has a heavy custom-fabricated wrought iron or powder-coated steel gate as a baseline feature. In Trousdale, many gates sit at severe uphill driveway grades where a swing gate physically cannot open without hitting grade, so slide operators are the only workable option. The original 1960s conduit runs feeding those operators are frequently undersized for modern 24V DC motors, which turns a simple motor swap into a full electrical rough-in before Beverly Hills code will sign off.
The marine layer off the Pacific sits on exposed gate hardware through much of the morning, which accelerates rust at welds, hinge pins, and bottom rollers on iron gates. Then the Santa Ana winds funnel through canyon mouths into the hills and put sudden lateral stress on large dual-leaf swing gates. We routinely find obstruction sensors that were calibrated on a calm afternoon and trip constantly when the wind picks up.
Our Main Beverly Hills Services
Beverly Hills homeowners call us most often for two things: repairing a gate that has stopped working and replacing a gate that no longer matches the property or the current code. Both start with a written scope and price before any tool is picked up.
Gate Repair in Beverly Hills
Repair work on Beverly Hills gates typically means diagnosing a motor that quit, a hinge that seized, a sensor that trips, or a leaf that scrapes the driveway. On older estates, we often find the original operator still in place with wiring that was never documented. Our Gate Repair in Beverly Hills page covers the repair process, response times, and what gets photographed and recorded on every visit. Every repair leaves you with a written record of what was found, what was set, and what was installed.
Gate Installation in Beverly Hills
Installation in Beverly Hills almost always involves the city’s permit process, which we handle from the initial scope through final inspection. The gates here are heavier than standard residential work, usually custom-fabricated, and often integrated into low masonry walls. For details on the installation path, permits, and what a full replacement includes, see Gate Installation in Beverly Hills. The price is written and handed over before any fabrication or site work begins.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Motor & Opener in Beverly Hills
Gate motor and opener work in Beverly Hills means servicing whatever is already on the property, whether that’s a European brand like FAAC or BFT on a Trousdale estate or an American linear arm on a flat-lot home south of Santa Monica Blvd. The marine layer corrodes exposed motor housings and limit switches, and the original conduit runs in hillside homes built in the 1960s are often too small for the current draw of modern operators. Our Gate Motor & Opener service covers nine automation brands, so we repair what is on the gate rather than steering you toward a replacement you don’t need.
Motor Installation
Signs you need it
The motor hums but the gate does not move, or the gate stalls halfway and reverses, or the existing operator is beyond economical repair.
What it costs in Beverly Hills
Motor installation in Beverly Hills typically ranges from $850 to $2,400 depending on the operator type, brand, and whether new conduit or wiring is required to meet city code.
How we do it
We document the existing wiring and limit-switch positions, pull the old operator, run any required electrical updates for Beverly Hills code compliance, mount and wire the new motor, set travel limits, and photograph every step for the job record.
Motor Repair
Signs you need it
The gate works intermittently, the motor makes a grinding or clicking sound, or the breakers trip only when the gate operates.
What it costs in Beverly Hills
Motor repair in Beverly Hills typically runs between $225 and $650 depending on whether the fault is a limit switch, capacitor, gear train, or control-board issue.
How we do it
We test the motor under load, isolate the failed component, replace only that part, reset travel limits and force settings, and leave a written record of the part number installed.
Linear Motor
Signs you need it
The linear arm extends partway, then stalls or jerks, or the arm bracket has pulled loose from the gate post.
What it costs in Beverly Hills
Linear motor replacement or repair in Beverly Hills usually falls between $500 and $1,100, with bracket repair or reinforcement adding to the total when the post has been stressed.
How we do it
We check arm travel against gate travel, verify the bracket is seated and square, set limit stops, and confirm the unit pulls within its rated force range before we finish.
Slide Motor
Signs you need it
The slide gate stops short of full travel, grinds on the rail, or the chain or belt jumps teeth under load.
What it costs in Beverly Hills
Slide motor replacement in Beverly Hills runs from $900 to $2,100, with additional cost when the rail or chain run must be rebuilt to match the new drive.
How we do it
We inspect the full rail run and chain tension, remove the old drive, mount the new motor, align the sprockets, set limit switches, and test the gate under repeated full cycles with the wind at its worst if it is blowing that day.
Intercom Integration
Signs you need it
The gate can be opened from the house but not from a call box, or a new intercom system is being installed and must trigger the existing motor.
What it costs in Beverly Hills
Intercom integration with an existing gate operator in Beverly Hills typically costs between $300 and $750 depending on relay work, wire pulls, and programming.
How we do it
We wire the intercom dry contact to the operator control board, test both entry and exit commands, and document the relay configuration so any future technician can read the setup without retracing it.
What Gate Motor & Opener Costs in Beverly Hills
| Item | Typical range in Beverly Hills |
|---|---|
| Motor repair | $225 - $650 |
| Linear motor replacement | $500 - $1,100 |
| Full motor installation | $850 - $2,400 |
How long does a gate motor repair take in Beverly Hills?
Most motor repairs in Beverly Hills are completed the same day we arrive, since we stock limit switches, capacitors, and control boards for nine operator brands. A full motor replacement with Beverly Hills permit work may take two to three days including inspection scheduling. Call (928) 260-0864 and we can tell you what the likely timeline is once we know the operator brand and symptom.
Does Beverly Hills require a permit to replace a gate motor?
Yes, when the work involves new electrical runs or operator replacement, Beverly Hills requires permits through its own building department. We handle the permit, schedule the inspection, and document the installation. Estimates are free and the written price covers the permit scope so there are no surprises at the end.
Gate Access Control in Beverly Hills
Gate access control in Beverly Hills means the systems that decide who may open the gate: keypads, remotes, phone entry, card readers, and video intercoms. The estate gates here are frequently paired with European operators, so American plug-and-play access panels don’t always communicate cleanly with the existing motor board. Our Gate Access Control service covers every common system on the market and we wire to whatever operator is already on the property.
Keypad Entry
Signs you need it
The keypad does not respond, a code works intermittently, or the keypad works but no longer triggers the gate.
What it costs in Beverly Hills
Keypad replacement or repair in Beverly Hills typically costs between $275 and $550 depending on whether new wiring must be pulled to the gate.
How we do it
We test the keypad output at the control board, replace the unit if the contacts are corroded, then program entry and exit codes and confirm every code fires the relay.
Remote Control
Signs you need it
One remote stopped working while the others still function, or range has dropped to nearly nothing.
What it costs in Beverly Hills
Remote programming or replacement in Beverly Hills generally runs from $150 to $350 including the new transmitter and receiver programming.
How we do it
We verify the receiver is hearing the transmitter, replace or reprogram the remote, and if range has degraded we check the receiver antenna placement rather than just handing you a faster remote.
Phone Entry
Signs you need it
Calls from the gate do not ring through, the gate can’t be opened from the phone, or the system drops after one ring.
What it costs in Beverly Hills
Phone entry repair or replacement in Beverly Hills falls between $400 and $900 depending on whether a cellular unit is needed because there is no landline at the gate.
How we do it
We check the phone line or cellular signal, test the relay at the operator board, and replace or reprogram the entry unit so calls ring and the open command fires on the first try.
Card Reader
Signs you need it
Cards work inconsistently, the reader clicks but the gate does not move, or new cards won’t enroll.
What it costs in Beverly Hills
Card reader service in Beverly Hills runs from $300 to $650 per reader, with additional programming cost when the system is tied to a managed access platform.
How we do it
We check the reader output at the controller, clean or replace the reader, enroll test cards, and confirm both the gate and the log record the entry.
Video Intercom
Signs you need it
Audio is clear but there is no video at the monitor, or the camera shows a black screen at night.
What it costs in Beverly Hills
Video intercom repair in Beverly Hills typically costs between $350 and $800 depending on camera, monitor, or wiring fault.
How we do it
We test the camera feed at the monitor, replace the camera or cable run if the signal is dead, and confirm video and audio both work before we leave.
What Gate Access Control Costs in Beverly Hills
| Item | Typical range in Beverly Hills |
|---|---|
| Keypad entry | $275 - $550 |
| Remote control | $150 - $350 |
| Phone entry system | $400 - $900 |
Can you integrate access control with an existing European gate operator in Beverly Hills?
Yes, and we do it often on Beverly Hills estates with FAAC, BFT, or Nice/Came operators. The access panel wires to the operator’s control board through the dry contact input. Call (928) 260-0864 and we will confirm compatibility before any hardware is ordered.
Is any access control work in Beverly Hills exempt from permits?
Low-voltage access control work is generally less involved than full operator replacement, but if we are pulling new conduit or adding a power supply, Beverly Hills code review may apply. We tell you in the written scope whether a permit is part of the job.
Gate Parts & Welding in Beverly Hills
Gate parts and welding in Beverly Hills means repairing the physical structure of a heavy custom gate: hinges, posts, rails, rollers, and the steel or iron itself. The marine layer that sits on these gates every morning accelerates rust in ways that a newer subdivision never deals with. Our Gate Parts & Welding service covers repairs that restore the gate’s structure, not just its automation.
Hinge Replacement
Signs you need it
The gate sags, scrapes the drive, or the hinge pins show visible rust bloom and metal loss at the joint.
What it costs in Beverly Hills
Hinge replacement in Beverly Hills runs from $400 to $750 per hinge, with heavier custom or surface-mounted hinges on estate gates running higher.
How we do it
We support the gate leaf, cut or unbolt the old hinge, weld or bolt the new one in alignment, and photograph the finished weld and hinge pin before lowering the gate.
Post Replacement
Signs you need it
The gate post wobbles at the base, the gate no longer closes square, or concrete around the post has cracked and lifted.
What it costs in Beverly Hills
Post replacement in Beverly Hills typically costs between $1,100 and $2,400 depending on post size, footing depth, and whether the surrounding masonry wall must be cut back for access.
How we do it
We remove the old post and footing, pour a new footing to depth, set and shim the new post square, and let the concrete cure before re-hanging the gate.
Rail Repair
Signs you need it
The slide gate jumps the rail, grinds mid-travel, or the rail has visible wear grooves in the middle third.
What it costs in Beverly Hills
Rail repair or section replacement in Beverly Hills runs between $500 and $1,200 depending on rail length and whether the supporting concrete pad must be patched first.
How we do it
We level the rail, replace worn sections, re-anchor loose hardware, and test the gate across the full travel before the operator is re-engaged.
Custom Welding
Signs you need it
A cracked weld at a joint, a bent section from a vehicle strike, or a broken picket that leaves the gate structurally compromised.
What it costs in Beverly Hills
Custom welding repairs in Beverly Hills start around $350 for single-joint crack repair and run to $1,200 or more for structural reinforcement at the frame corners.
How we do it
We grind the affected area, weld with matched filler, grind the bead for a clean finish, and optionally prime and paint the repair to match the surrounding gate.
Gate Rollers
Signs you need it
The gate drags, the roller wheels are flattened, or the bottom rail sits visibly lower on one side.
What it costs in Beverly Hills
Gate roller replacement in Beverly Hills typically costs between $250 and $550 per set depending on gate weight and roller diameter.
How we do it
We lift the gate slightly, pull the worn rollers, seat the new rollers in the track, and adjust the carrier so the gate rides level though the full cycle.
What Gate Parts & Welding Costs in Beverly Hills
| Item | Typical range in Beverly Hills |
|---|---|
| Hinge replacement | $400 - $750 per hinge |
| Rail repair | $500 - $1,200 |
| Post replacement | $1,100 - $2,400 |
How urgent is a cracked weld on a Beverly Hills gate?
Urgent enough to address before the next Santa Ana wind event. A cracked weld on a large dual-leaf gate under lateral wind load can propagate quickly and drop a leaf. Call (928) 260-0864 and we will give you a written price before any welding starts.
Do you weld on site or take the gate back to a shop?
Most repair welding is done on site in Beverly Hills so the gate stays aligned on its hinges and track. For long fractures or frame reinforcement, we set up on site with a portable rig and photograph every pass for the job record.
Brands We Service in Beverly Hills
We service nine gate-automation brands including Ghost Controls, DoorKing, Elite, and Mighty Mule, which covers most of what is already on Beverly Hills properties. Parts for these brands are stocked locally near Los Angeles, so repair turnaround is typically same day. See our brands for the full list and what we carry.
Pricing for Gate Repair in Beverly Hills, CA
| Service | Typical range in Beverly Hills |
|---|---|
| Motor repair | $225 - $650 |
| Linear motor replacement | $500 - $1,100 |
| Full motor installation | $850 - $2,400 |
| Keypad entry | $275 - $550 |
| Remote control | $150 - $350 |
| Phone entry system | $400 - $900 |
| Hinge replacement | $400 - $750 per hinge |
| Rail repair | $500 - $1,200 |
| Post replacement | $1,100 - $2,400 |
| Gate roller replacement | $250 - $550 per set |
Prices in Beverly Hills tend to run at the upper end when the gate is a heavy custom fabrication, when hillside access requires extra rigging, or when the existing conduit must be rebuilt to meet city code. Every price is written and handed to you before work starts, so the invoice and the quote match.
Neighborhoods We Serve in Beverly Hills
We work throughout Beverly Hills, from the estates in the flats south of Santa Monica Blvd to the hillside homes of Trousdale Estates and the canyon-adjacent streets where wind loading changes gate behavior. Response time across the city is typically same day for repair calls.
- Trousdale Estates
- Beverly Hills Flats
- The Golden Triangle area
- Beverly Park
- Coldwater Canyon adjacent streets
Service Area - Cities Near Beverly Hills
From Beverly Hills, we also cover nearby communities including West Hollywood, CA, Studio City, CA, Universal City, CA, and Culver City, CA. Dispatch is coordinated from our Los Angeles office, and crews serve Beverly Hills locally with the same written-price and photo-record standard on every job.
Serving Beverly Hills, CA - Our Local Coverage Area
We’re based in the Beverly Hills area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Beverly Hills
Most repair calls in Beverly Hills get same-day service when we are called before early afternoon. A live person answers at (928) 260-0864 around the clock, and we name the technician and give you a written price before any work starts. Emergency calls are handled through the same number.
Yes for operator installation, new electrical runs, or structural changes. Beverly Hills has its own building and permit department, separate from LADBS, and the inspections are city-run. We handle the permit scope in the written estimate so the process doesn’t stall on paperwork.
Every completed job is covered by the 365-Day Done Right Promise. If the repair is not right within a full year, Vance makes it right at no additional charge. That applies to motor work, access control, and welding repairs throughout Beverly Hills.
If your gate is not behaving the way it should in Beverly Hills, call (928) 260-0864. A live person answers, the diagnostic is methodical, and the price is written before any work begins. You will get a photo record of what was found and what was set before the technician leaves.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Beverly Hills Customers Say
"Good work on a long driveway gate. Arrived when they said, finished when they said."
- Sofia E."Honest about what did not need doing. Told me the operator had years left and only the control board needed replacing."
- Douglas N."Quoted in writing, installed on the day promised, and the price did not move. The crew was licensed and the number was on the paperwork."
- Wes A.