Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Norman, OK
Gate motor and opener failure is the most common call we handle in Norman, and it usually starts the same way: the motor hums, the gate moves six inches, then stops. In a city where expansive clay soil heaves gate posts seasonally and spring storms push frames out of alignment, the motor is rarely the whole story. We find the limit switches fighting a post that moved, the gearbox working against a sagging rack, or the photo-eye misaligned because the post it was mounted to shifted in wet ground. Call (928) 260-0864 and we’ll put a written price in your hand before anyone picks up a tool.
Why Norman Homes Are Different
Norman sits in the middle of Tornado Alley, and the NOAA National Weather Center on the south side of town is there for a reason. After a spring severe weather season, we see gates on south and west exposures with blown hinges, sheared posts, and frames warped by straight-line winds. But the more persistent problem is under the gate: central Oklahoma’s expansive clay swells in wet springs and shrinks in dry summers, tilting posts out of plumb and causing latch and swing misalignment that has nothing to do with a storm. A gate that closed fine in March can bind by June because the soil under the post changed volume. South Norman subdivisions built out heavily in the 1980s through the 2000s now have large numbers of similarly aged wooden privacy gates and ornamental iron driveway gates hitting end-of-hardware-life at the same time. Near the OU campus, original chain-link and wrought-iron gates from the 1940s through the 1960s often sit on posts set in crumbling concrete footings. Winter ice storms add another layer: frozen precipitation loads the frame and hardware, then the thaw cycle shifts everything again.
Our Main Norman Services
Two services dominate calls from Norman homeowners: repair work on gates that stopped operating correctly, and full installations when a gate has passed the point where repair makes sense. Here’s what each involves in Norman specifically.
Gate Repair in Norman
Repair work in Norman usually traces back to the soil and the weather. Hinges seize after rust and clay dust work into the pins. Posts tilt as the ground beneath them expands. Frames warp under ice loading or storm wind. We repair the gate while accounting for the local conditions that caused the failure, and every repair leaves with a documented photo record of what was found and what was set. For a full picture of repair scope, see Gate Repair in Norman.
Gate Installation in Norman
New installations in Norman require footings sized for clay soil movement and materials chosen for ice and wind exposure. A south-facing ornamental iron gate takes different stresses than a shaded backyard privacy gate near the OU campus. We quote installation in writing, with the footing depth, material specification, and operator model named on the quote. More detail is on the Gate Installation in Norman page.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Motor & Opener in Norman
Gate motor and opener service in Norman is about matching the operator to what the soil and storms have done to the gate. Most 1990s and 2000s south Norman homes have operators that were sized for a gate that weighed less and sat on posts that were still plumb; a decade of clay movement later, the motor is working against forces it was never rated for. That’s the core of what we do: diagnose the operator, correct the mechanical alignment, and set the limits and force settings so the motor stops fighting the gate. This work is covered under our Gate Motor & Opener service, and we work on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule.
Motor Installation
Signs you need it
The existing motor trips its breaker, the control board shows error codes that repeat after reset, or the gearbox whines and the gate moves slower each week.
What it costs in Norman
Most motor replacements in Norman run $850-$2,100 depending on brand and whether the arm bracket, receiver, and wiring are reusable.
How we do it
We pull the failed operator, check the mounting plate and arm geometry against the gate’s actual post position, install the new motor, set travel limits and force, and photograph every setting before we leave.
Motor Repair
Signs you need it
The motor runs but the gate doesn’t move, or the gate reverses mid-travel, or you hear a click but no motion when you press the remote.
What it costs in Norman
Motor repairs in Norman typically run $150-$450, with control board replacement at the higher end and limit switch or capacitor work at the lower end.
How we do it
We read the limit positions first, check voltage at the board, test the capacitor and gearbox, replace the failed component, and hand you a written record of the part number and the new settings.
Linear Motor
Signs you need it
Your Linear operator stops responding to remotes, moves only a few inches, or shows a flashing light code that won’t clear after a power cycle.
What it costs in Norman
Linear motor service in Norman follows the same range as other brands: $150-$450 for repair, $850-$2,100 for full replacement when the unit is beyond service.
How we do it
We diagnose the Linear board and motor using the brand’s documented test procedure, confirm the failure, then repair or replace with the correct Linear part rather than substituting a generic component.
Slide Motor
Signs you need it
Your sliding gate shudders, stalls halfway, or the motor strains audibly and the gate moves slower than it did a year ago.
What it costs in Norman
Slide motor service in Norman runs $150-$450 for repair work and $850-$2,100 for replacement, with the final number depending on the track condition and the existing motor brand.
How we do it
We check the track for clay debris and wear, clear the rack, verify the motor sprocket and chain alignment, then set torque and limits to match the gate’s actual weight and travel.
Intercom Integration
Signs you need it
You have an intercom or call box at the gate that isn’t triggering the motor, or you’re adding a phone-based entry system that needs to talk to the existing operator.
What it costs in Norman
Intercom-to-motor integration in Norman runs $180-$550, depending on whether we’re pulling new wire or tying into existing low-voltage runs.
How we do it
We open the motor’s control board, wire the intercom relay output to the correct input terminals, set the open-command behavior, and test the full call-to-open sequence before we leave.
What Gate Motor & Opener Costs in Norman
| Item | Typical range in Norman |
|---|---|
| Motor repair (limit switch, capacitor, board diagnosis) | $150-$450 |
| Motor replacement (most brands and models) | $850-$2,100 |
| Intercom or phone-entry integration | $180-$550 |
Can you fix a gate motor the same day in Norman?
Yes. Most motor repairs in Norman are same-day or next-day. We stock common LiftMaster, Linear, and BFT boards and parts locally. Call (928) 260-0864 for a written upfront price.
Why does my Norman gate motor work in winter but fail in spring?
Clay soil under the posts swells in spring rains, shifting the post and throwing the travel limits off. The motor then stalls on obstruction detection. We reset limits to the post’s actual position. Call (928) 260-0864 for a documented fix.
Gate Access Control in Norman
Access control in Norman means one thing above all: the entry point has to work correctly even when the power hasn’t been reliable and the weather has been rough. Ice storms knock out power in Norman often enough that battery backup on access control matters; a keypad or card reader that resets to factory default after every outage is a real liability. We install and repair access control so it holds programming through outages and works with the gate’s existing motor, whatever brand is on the post. That work lives under our Gate Access Control service.
Keypad Entry
Signs you need it
The keypad intermittently fails to open the gate, or the code works for one family member but not another, or the keypad face is cracked and fills with water after rain.
What it costs in Norman
Keypad entry repair in Norman runs $120-$340; a full keypad replacement with programming is $180-$550.
How we do it
We test the keypad output at the control board, check for water damage in the housing, replace the unit if needed, and program all codes on site while you test them.
Remote Control
Signs you need it
Remotes lose programming after storms, open the gate randomly, or one vehicle’s remote works while another’s doesn’t.
What it costs in Norman
Remote programming and receiver work in Norman runs $120-$340, including a new receiver if the existing one has failed.
How we do it
We check the receiver antenna and ground, test the remote’s frequency against the receiver’s documented spec, relearn all remotes to the system, and hand you a written list of which remotes are active.
Phone Entry
Signs you need it
Visitors call the gate line and the call doesn’t ring through, or the call rings but the touch-tone command won’t open the gate.
What it costs in Norman
Phone entry in Norman runs $180-$550 installed and programmed, depending on whether the system is cellular or landline-based.
How we do it
We verify the phone line or cellular module, wire the entry unit to the gate operator’s open-command input, program the access numbers, and test the full call-to-open path before leaving.
Card Reader
Signs you need it
Cards work intermittently, the reader rejects every card after a power cycle, or you need to add new card credentials and the existing reader won’t accept them.
What it costs in Norman
Card reader service in Norman runs $150-$450 for repair; a new reader with credential programming is $250-$700.
How we do it
We test the reader output at the controller, verify the card format matches the reader spec, replace the reader if needed, and enroll all credentials while you watch the gate respond.
Video Intercom
Signs you need it
The video feed is black, the intercom audio cuts out in wind, or the call rings through but there’s no way to see who’s at the gate.
What it costs in Norman
Video intercom repair in Norman runs $180-$550; full video intercom installation with a new monitor and camera is $800-$2,000.
How we do it
We check the camera’s power and video feed, replace or re-aim the camera, verify the indoor monitor’s range, and test call and open functions from both the monitor and the gate.
What Gate Access Control Costs in Norman
| Item | Typical range in Norman |
|---|---|
| Keypad or remote receiver repair | $120-$340 |
| Phone or intercom integration | $180-$550 |
| Card reader or video intercom install | $250-$2,000 |
Will my gate access control lose programming after a Norman ice storm?
It shouldn’t if battery backup is installed and programmed correctly. We install and test backup so keypad and card credentials survive a power loss. Call (928) 260-0864 for a written check.
Can you program my existing card reader, or do I need a new one?
We can program most readers we service. We’ll test the old unit first and tell you in writing whether programming or replacement is the honest fix. Call (928) 260-0864 for a free estimate.
Gate Parts & Welding in Norman
Parts and welding work in Norman is where the clay soil puts the most stress on a gate. Posts move through the seasons, hinges carry more weight than they were rated for, and welds crack under the repetition. Most of what we do in this category is mechanical: replacing the worn part, re-welding the cracked joint, and setting the gate so the repaired section isn’t taking more load than it should. See Gate Parts & Welding for the full scope of what we cover.
Hinge Replacement
Signs you need it
The gate drags on the latch side, the hinge pin is visibly worn or bent, or the gate sags enough that the latch no longer lines up.
What it costs in Norman
Hinge replacement in Norman runs $120-$380, depending on gate weight and whether we need to weld the new hinge to the post or bolt it.
How we do it
We measure the gate’s actual weight and post position, select a hinge rated for that load, remove the old hinge, weld or bolt the new one, and realign the latch before leaving.
Post Replacement
Signs you need it
The post leans more than a few degrees, the concrete footing is cracked and crumbling, or the gate binds at the top or bottom because the post has moved.
What it costs in Norman
Post replacement in Norman runs $250-$800 per post, including digging out the old footing, setting a new post in concrete sized for the clay soil, and re-hanging the gate.
How we do it
We dig out the failed footing, set the new post in concrete mixed for expansive soil conditions, brace it plumb while the concrete cures, then re-hang the gate and set the latch.
Rail Repair
Signs you need it
Your sliding gate’s rail is bent, rusted through, or the wheels bind at one point along the track.
What it costs in Norman
Rail repair in Norman runs $180-$650, depending on whether we’re splicing a section or replacing the full rail run.
How we do it
We pull the gate off the track, cut out the damaged rail section, weld in new rail matched to the existing profile, and test the full travel before re-hanging.
Custom Welding
Signs you need it
A weld has cracked at a stress point, the frame is splitting, or you need a reinforced mounting plate for a new operator.
What it costs in Norman
Custom welding in Norman runs $150-$600 per repair point, priced by the inch of weld and the access involved.
How we do it
We grind out the cracked weld, prep the joint, re-weld with the correct rod for the gate’s metal, and photograph the finished weld for your record.
Gate Rollers
Signs you need it
The gate grinds or squeals as it slides, or one wheel has flat-spotted and the gate hops at that point.
What it costs in Norman
Gate roller replacement in Norman runs $120-$380 per set, including bearing service and track cleanup.
How we do it
We lift the gate off the track, press out the old roller bearings, install new sealed rollers, clean the track of clay and debris, and test the full slide range.
What Gate Parts & Welding Costs in Norman
| Item | Typical range in Norman |
|---|---|
| Hinge replacement | $120-$380 |
| Post replacement (per post) | $250-$800 |
| Rail repair or custom welding | $150-$650 |
How long does a welded gate repair last in Norman?
A correctly welded joint on a properly aligned gate lasts years, but if the post that caused the crack is left leaning, the weld will fail again. We fix the root cause. Call (928) 260-0864 for a written assessment.
Can you fix a gate post that the clay soil pushed out of plumb?
Yes. We excavate the old footing, set the post in concrete sized for Norman’s expansive clay, and re-hang the gate. Price is written before we start. Call (928) 260-0864.
Brands We Service in Norman
We service nine automation brands across Norman, including LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. We stock common BFT, Linear, and Viking parts locally, which keeps most motor repairs to a same-day or next-day turnaround. See our brands for the full list and what we keep on hand.
Pricing for Gate Repair in Norman, OK
| Service | Typical range in Norman |
|---|---|
| Motor repair | $150-$450 |
| Motor replacement | $850-$2,100 |
| Keypad or remote receiver repair | $120-$340 |
| Phone or intercom integration | $180-$550 |
| Card reader or video intercom install | $250-$2,000 |
| Hinge replacement | $120-$380 |
| Post replacement (per post) | $250-$800 |
| Rail repair or custom welding | $150-$650 |
| Gate roller replacement | $120-$380 |
Prices in Norman push toward the higher end of these ranges when clay soil movement has thrown the gate far out of alignment, because we have to correct the post position before the motor or hardware work can hold. Every price is written and agreed before any work starts, so the number on the quote is the number on the invoice.
Neighborhoods We Serve in Norman
We cover all of Norman, from the older streets near the OU campus to the south Norman subdivisions built in the 1980s and 2000s. Response time across the area is typically same-day for motor and access control repairs.
- South Norman
- Near the OU campus
- West Norman
- East Norman
- Lake Thunderbird area
Service Area - Cities Near Norman
We also serve the surrounding central Oklahoma cities. Gate work in Mustang, OK, Oklahoma City, OK, Yukon, OK, and Edmond, OK follows the same written-price, documented-record standard. Dispatch is coordinated from the brand’s Oklahoma City office; crews serve Norman locally.
Serving Norman, OK - Our Local Coverage Area
We’re based in the Norman area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Norman
Most motor and access control repairs in Norman are same-day or next-day. Parts jobs may take an extra day if a specific hinge or roller size isn’t on the truck. Call (928) 260-0864 and we’ll give you a straight answer on timing.
Most repairs don’t require a permit, but full gate installations and new post footings in certain Norman neighborhoods do. We’ll tell you in writing if your job needs one and what it covers. Call (928) 260-0864 before you start the project.
Yes. Many south Norman HOA communities have specific gate style and material requirements. We’re familiar with the common restrictions and will confirm compliance before we quote. The price stays written and fixed. Call (928) 260-0864.
For a written, upfront price on any gate motor, access control, or parts and welding work in Norman, call (928) 260-0864. A live person answers 24/7, and the price you’re quoted is the price you pay.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Norman Customers Say
"Quoted in writing, installed on the day promised, and the price did not move. The crew was licensed and the number was on the paperwork."
- Wes A."Gate had been dragging for a year. They photographed the bent hinge post, explained why the operator kept faulting, and gave me a fixed price to correct both."
- Terrence B."They installed the opener and left me a diagram of the wiring and the limit settings. When I needed a second remote programmed I could do it myself."
- Nadine C.