Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Marietta, GA
Gate motor and opener failure in Marietta usually traces back to two things: the age of the operator and what Georgia red clay has done to the posts holding everything in line. The East Cobb corridor is dense with ornamental iron driveway gates installed in the 1980s through 2000s, and those operators are now 20 to 30 years old, failing in batches as their limit switches, control boards, and gearboxes reach the end of their service life. We diagnose the motor, the wiring, and the gate structure together, because in this soil they fail together. Call (928) 260-0864 and you’ll get a live person, a scheduled dispatch, and a written price before any tool comes off the truck.
Why Marietta Homes Are Different
Marietta’s gate repair profile is dominated by one local fact: the heavy clay soil under Cobb County expands and contracts through Georgia’s wet-dry cycles, and every cycle moves gate posts. A swing gate that was perfectly plumb when the subdivision went in during the 1990s has spent three decades absorbing seasonal heave. Technicians working East Cobb zip codes like 30062 and 30068 routinely find cracked mortar at the base of brick gate pillars, with the entire pillar tilting inward toward the driveway. The gate operator did not fail. The foundation under it shifted, and the operator has been fighting that misalignment on every cycle.
The housing stock compounds the problem. Marietta ranges from antebellum homes near the historic Square to brick-front colonials and craftsman homes built across East Cobb and West Marietta from the late 1970s through the mid-2000s. The latter generation, the one now calling for gate service, often runs Viking, LiftMaster, or Elite swing-gate operators that are well past their intended service life. Add humid subtropical summers that accelerate rust and paint failure on steel and iron, plus the occasional North Georgia ice event that stresses already weakened hinges and operators, and the local repair market is consistently busiest on structural and mechanical failures that look, at first glance, like an electrical problem. In Marietta, you have to check the post before you condemn the board.
Our Main Marietta Services
Two services account for most of the calls from Marietta driveways: repair of existing gates that have stopped operating, and full installation when repair no longer makes sense. Both start the same way, with one of our technicians on site, a written scope of work, and a flat price agreed before anything gets touched.
Gate Repair in Marietta
Repair work in Marietta usually means finding the mechanical or electrical fault, not replacing the gate wholesale. A stuck swing gate may need a hinge replacement, a post reset, a new limit switch, or a motor repair, and the difference matters because the price difference is substantial. Homes in East Cobb and West Marietta built from the 1980s onward often have ornamental iron or tubular steel gates still worth repairing, and we treat replacement as a last resort, not a first suggestion. Every repair includes a photo record of what was found, what was adjusted, and what was replaced, left with you and filed in the job record. See Gate Repair in Marietta for the full scope of repair work.
Gate Installation in Marietta
Installation in Marietta has to account for the soil before the gate ever gets hung. New posts need concrete footings sized for our clay expansion cycles, and a gate that will survive here needs corrosion protection from day one, not as an afterthought. Whether it’s a swing gate on brick pillars in East Cobb or a slide gate on a West Marietta lot, the installation includes setting posts in soil we know will move, mounting the operator, wiring power, and setting safety edges and photo-eyes before the system is tested under load. We write the full scope and price before ordering anything. See Gate Installation in Marietta for what a full install includes.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Motor & Opener in Marietta
Gate motor and opener failures in Marietta fall into a pattern: the operator on a 1990s or early-2000s swing gate stops responding, and the owner assumes the motor is dead when the actual fault is often a limit switch that has drifted or a control board fighting a post that shifted out of plumb. Our Gate Motor & Opener work starts with reading the limit switch positions and checking the gate’s travel path, because in this soil a misaligned post presents as a motor symptom. We service nine automation brands including LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, so whatever is already on the property, the repair starts with the existing motor rather than a sales pitch for replacement.
Motor Installation
Signs you need it
The gate moves in jerks, stops mid-travel, or the existing motor makes a grinding sound and trips the breaker.
What it costs in Marietta
A swing-gate motor replacement in Marietta typically runs $600 to $1,300 depending on brand and whether the arm bracket is intact, while slide-gate motor installation runs $900 to $1,850.
How we do it
We remove the old operator, mount the new motor on the existing structure or a corrected bracket, set the limit switches to the gate’s actual travel, wire the power and safety inputs, and photograph every connection before we leave.
Motor Repair
Signs you need it
The motor hums but the gate doesn’t move, or the gate opens on its own but refuses to close.
What it costs in Marietta
Gate motor repair and troubleshooting costs $125 to $350, with the exact flat price written after the diagnosis and before any repair part is touched.
How we do it
We trace the fault from the control board through the limit switches to the motor, test each component under load, and replace only the failed part, with the old part returned to you and photos of the new one installed.
What Gate Motor & Opener Costs in Marietta
| Item | Typical range in Marietta |
|---|---|
| Gate motor repair and troubleshooting | $125 - $350 |
| Swing-gate motor replacement | $600 - $1,300 |
| Slide-gate motor replacement | $900 - $1,850 |
Can you fix a gate motor the same day in Marietta?
Yes, most motor repairs in Marietta are completed the same day we arrive, because we carry common control boards, limit switches, and capacitors on the truck. For a full motor replacement, we typically complete the job on the first visit unless the post or bracket needs structural correction first.
Call (928) 260-0864 and we’ll tell you the next open dispatch window and what we’ll check first.
Do you work on the motor already on my Marietta gate, or push a replacement?
We repair the motor already on the gate whenever it’s repairable. We service BFT, Linear, Viking, Ghost Controls, and five other brands, so the existing manufacturer doesn’t limit us, and we quote the repair price in writing before any replacement is ever discussed.
If you have the motor’s brand and symptom ready, call (928) 260-0864 for an exact repair quote before we even roll.
Gate Access Control in Marietta
Access control in Marietta usually enters the picture when a homeowner wants a gate that opens for the people who belong and stays closed for everyone else, without handing out a garage-door clicker to every contractor and neighbor. The systems we see here run from simple keypads on East Cobb ornamental gates to phone-entry and video intercom panels on newer West Marietta installs. Our Gate Access Control work integrates with whatever operator is already mounted, since we service all nine major brands, and the job includes programming the codes, testing every input, and photographing the final configuration.
Keypad Entry
Signs you need it
The keypad stops accepting the code, works intermittently in wet weather, or the housing has cracked and let moisture reach the circuit board.
What it costs in Marietta
Keypad installation for a single gate in Marietta ranges from $350 to $1,200 depending on whether it ties into a telephone entry system or a simple relay.
How we do it
We install the keypad, wire it to the operator’s open input, program the entry codes while you watch, and seal the housing against Marietta humidity before testing it through several cycles.
Phone Entry
Signs you need it
Visitors can’t reach you when the gate is closed and you want them to call a number that opens the gate rather than propping the gate open for the afternoon.
What it costs in Marietta
Telephone entry systems in Marietta run $900 to $2,000 installed, including the controller, wiring to a phone line or cellular module, and programming the directory.
How we do it
We mount the entry panel, run the wiring to the controller, connect it to the gate operator’s input, and program the call-to-open numbers before demonstrating the full call flow with you.
What Gate Access Control Costs in Marietta
| Item | Typical range in Marietta |
|---|---|
| Keypad entry (single gate) | $350 - $1,200 |
| Telephone entry system | $900 - $2,000 |
| Card reader or video intercom add-on | $450 - $1,100 |
Will a keypad survive a Marietta summer?
Yes, if it’s sealed correctly and the enclosure is rated for outdoor exposure. We have replaced keypads in East Cobb that failed after two humid summers because the installer didn’t seal the conduit entry, and water wicked up into the board.
Call (928) 260-0864 and we’ll check the existing keypad’s seal or quote a new one installed properly.
Can I add phone entry to the gate I already have in Marietta?
In most cases, yes. Phone entry ties into the open input on any of the nine operator brands we service, so the existing motor doesn’t need to be replaced, only wired to the new controller.
Call (928) 260-0864 with the gate’s operator brand and we can tell you over the phone whether it has an open input we can use.
Gate Parts & Welding in Marietta
Marietta’s red clay movement makes the structural side of gate repair as important as the electrical side, and that’s where Gate Parts & Welding comes in. A hinge that worked fine for twenty years gives out when the post it is bolted to shifts a half inch out of line, and the repair is not just a new hinge but a corrected post and a rehung gate. We weld on site in Marietta, fix cracked ornamental iron, replace failed hinges, and reset posts into footings sized for our soil, then document every weld and every part number.
Hinge Replacement
Signs you need it
The gate sags enough to drag on the driveway, the hinge bolts show rust staining, or the gate makes a creaking sound at one corner even after lubrication.
What it costs in Marietta
Hinge replacement on a standard ornamental iron gate in Marietta typically runs $180 to $400 per hinge depending on gate weight and whether welding is required.
How we do it
We lift the gate off its pins, cut or unbolt the failed hinge, weld or bolt the new hinge in place, rehang the gate, and adjust the operator’s limits to match the corrected swing.
Custom Welding
Signs you need it
A picket has cracked through at the weld, the gate frame has split at a corner, or the operator bracket has torn away from the gate structure.
What it costs in Marietta
Custom welding for a crack repair or bracket fix in Marietta ranges from $150 to $600 depending on access, prep, and the thickness of the steel involved.
How we do it
We grind the crack clean, weld it with the gate in place or removed as needed, re-coat the repair, and photograph the finished weld before we declare the gate sound.
What Gate Parts & Welding Costs in Marietta
| Item | Typical range in Marietta |
|---|---|
| Hinge replacement (per hinge) | $180 - $400 |
| Post reset or replacement | $500 - $1,750 |
| Custom welding (crack or bracket repair) | $150 - $600 |
Why do gate posts lean in Marietta specifically?
The red clay soil in Cobb County expands when wet and shrinks when dry, and over years that cycle pushes posts out of plumb. A pillar that was set shallow in the 1990s may now lean inward enough that the gate binds on every open cycle.
Call (928) 260-0864 and we’ll measure the post’s lean and tell you whether it needs resetting before the operator gets adjusted again.
Can you weld my existing ornamental gate, or do I need a new one?
We can weld most ornamental iron and tubular steel gates in Marietta, including crack repairs, broken pickets, and bracket failures. Replacement only comes up when the frame itself is rusted through in multiple places and a weld would fail within the year.
Bring photos of the damage when you call (928) 260-0864 and we’ll tell you which side of that line your gate is on.
Brands We Service in Marietta
We carry parts for and service LiftMaster, Viking, Elite, FAAC, BFT, Linear, Ghost Controls, DoorKing, and Mighty Mule operators on Marietta gates. Stock for common failures includes control boards, limit switches, capacitors, and photo-eyes, so most repairs finish the same day. See our brands page for the complete list and what we stock per brand.
Pricing for Gate Repair in Marietta, GA
| Service | Typical range in Marietta |
|---|---|
| Gate motor repair and troubleshooting | $125 - $350 |
| Swing-gate motor replacement | $600 - $1,300 |
| Slide-gate motor replacement | $900 - $1,850 |
| Keypad entry (single gate) | $350 - $1,200 |
| Telephone entry system | $900 - $2,000 |
| Card reader or video intercom add-on | $450 - $1,100 |
| Hinge replacement (per hinge) | $180 - $400 |
| Post reset or replacement | $500 - $1,750 |
| Custom welding (crack or bracket repair) | $150 - $600 |
Two things push Marietta prices toward the higher end of the ranges above: a post that has shifted out of plumb and must be corrected before any operator work will hold, and operators installed before 2010 that may need a new control board because the manufacturer discontinued the old one. Either way, the flat price is written and handed to you before any work begins, under Haven Standard Clause 1, and it does not change at the end of the job.
Neighborhoods We Serve in Marietta
We dispatch technicians across Marietta daily, from the historic neighborhoods around the Square to the subdivisions spreading east along Johnson Ferry and Roswell roads. The soil and the gate stock vary block to block, but our response time is the same: a live person answers, we tell you the next open window, and the tech arrives with a name and photo sent ahead.
- East Cobb
- West Marietta
- Historic Marietta Square area
- Johnson Ferry corridor
- Sandy Plains
Service Area - Cities Near Marietta
We serve all of Marietta and the surrounding metro areas, including Smyrna, TN on the Tennessee side and Kennesaw, GA just to the north. For gates closer to the city, see Atlanta, GA or Mableton, GA to the southwest. If you’re near a Marietta boundary, call (928) 260-0864 and the live dispatcher will confirm your address is in our daily route.
Serving Marietta, GA - Our Local Coverage Area
We’re based in the Marietta area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Marietta
Most gate repairs on existing structures in Marietta do not require a permit, but a full new installation with new posts and electrical wiring may trigger city or county review. We handle the scope and any permit paperwork as part of the written price, so you’re not left navigating Cobb County requirements on your own, and we’ll confirm what applies to your specific property before work starts.
A live person answers our phone 24/7 and can typically offer a same-day or next-day dispatch window in most Marietta neighborhoods depending on the day’s route. We don’t queue callbacks or route through an answering service. Call (928) 260-0864, give the address and the symptom, and we’ll commit to a window before you hang up.
Yes, it is the single most common root cause we document in Marietta. Georgia clay expands and shrinks with moisture, and over years that movement heaves posts and shifts brick pillars, which then misaligns the gate and overloads the operator. We photograph the post positions and the gate’s travel on every visit so you have a record of whether the clay is moving your gate, and how much.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Marietta Customers Say
"Quoted in writing, installed on the day promised, and the price did not move. The crew was licensed and the number was on the paperwork."
- Wes A."Gate had been dragging for a year. They photographed the bent hinge post, explained why the operator kept faulting, and gave me a fixed price to correct both."
- Terrence B."They installed the opener and left me a diagram of the wiring and the limit settings. When I needed a second remote programmed I could do it myself."
- Nadine C.