Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Kearny, NJ
Gate motor and opener repair in Kearny, NJ most often means one of two things: a swing gate that has pulled its post out of plumb after a Passaic River flood event, or an older slide gate on a tight lot that has ground its rollers down against rusted track. The housing stock here, early-to-mid 20th century two-family homes on 25 to 30 foot lots, means nearly every property has a side-yard gate along a narrow alley passage, and many of those original tubular-steel units are still in service. A failed opener on a Kearny gate usually traces back to water intrusion at the control board or a limit switch that was never reset after the gate frame shifted. Call (928) 260-0864 and we will give you a written price before any work starts.
Why Kearny Homes Are Different
Kearny sits low along the Passaic River, and large sections of town near the Kearny Marsh and the riverside flats flood with enough regularity that saturated gate-post footings are not an occasional problem here, they are the defining one. After a documented Passaic River overflow, we find gate posts along affected blocks leaning or fully heaved, and the repair is a post-reset with new concrete rather than a hinge adjustment. That is different from upland towns like North Arlington or Lyndhurst, where freeze-thaw works on dry soil and posts stay put for years.
The housing stock compounds it. Narrow lots mean side gates sit close to foundation walls, so drainage from downspouts often pours directly onto the post footing. Kearny’s active and former industrial parcels along Route 7 and the Belleville Turnpike add heavy-duty chain-link slide gates and swing-arm commercial gates to the mix, and road salt from truck traffic on those corridors accelerates rust on steel frames noticeably faster than in residential-only communities nearby. A gate repair call in Kearny is rarely a simple motor swap; it is usually a footing, a frame, and a motor working as one system.
Our Main Kearny Services
Two services account for most of what Kearny homeowners call us about: repairing an existing gate that has stopped working, and installing a new gate where none exists or where the old one is beyond saving. Both start the same way, with a written price before any work begins.
Gate Repair in Kearny
Most repair calls in Kearny involve a gate that binds against the post, a motor that runs but does not move the gate, or a hinge that has rusted through after years of river humidity and road salt. We inspect the full system, not just the part that failed, because a shifted post will destroy a new hinge or motor within months if it is not addressed first. You get a photo record of what we found and what we replaced. See Gate Repair in Kearny for the full breakdown.
Gate Installation in Kearny
New gate installation in Kearny has to start with the footing, especially on the flood-prone streets near the marsh. We spec concrete depth and post gauge for soil that will get saturated, not for an ideal dry-year scenario, and we measure the actual opening rather than working from the old gate’s dimensions, which are often out of square. See Gate Installation in Kearny for what a full install includes.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Motor & Opener in Kearny
Gate motor and opener work in Kearny skews toward two failure patterns: swing-arm motors that have stripped a gear fighting a post that shifted after a flood event, and slide-gate motors on industrial-corridor properties that have ingested years of road salt and grit through worn seals. Older tubular-steel gates on the town’s two-family lots are often heavy enough that an undersized opener from the original build is working at its limit, which burns boards and capacitors on schedule. The fix is usually not a full gate replacement; it is a correctly-sized motor, re-plumbed posts, and a documented limit-switch reset. We service what is already on the property rather than steering toward replacement, across nine automation brands including Ghost Controls, DoorKing, and Linear. For the full scope of opener work, see Gate Motor & Opener.
Motor Installation
Signs you need it
The existing opener runs nonstop, trips its breaker, or will not move the gate even after a manual release and re-latch, and the motor housing shows water staining or rust around the seams.
What it costs in Kearny
Motor installation in Kearny typically runs $650 to $1,500 depending on brand and whether the arm bracket and mounting plate are still serviceable.
How we do it
We remove the old unit, check the post and hinge alignment before mounting anything, install and program the new motor, and photograph every setting and connection before we leave.
Motor Repair
Signs you need it
The gate opens halfway and reverses, the motor hums without moving, or the control board shows a fault code that recurs after a reset.
What it costs in Kearny
Motor repair in Kearny lands between $180 and $450 for most capacitor, limit-switch, and gear-drive failures we see after flood events or salt exposure.
How we do it
We test the board, limit switches, and capacitor in place, replace only the failed part, reset travel limits to the actual gate path, and leave you the photo log of the readings.
What Gate Motor & Opener Costs in Kearny
| Item | Typical range in Kearny |
|---|---|
| Motor repair (capacitor, limit switch, gear) | $180 - $450 |
| Motor replacement | $650 - $1,500 |
| Complete opener system (motor + arms + controls) | $1,200 - $2,800 |
Can you fix a flood-damaged gate opener the same day?
In most cases, yes. If the motor housing took on water, we dry and test the board on site, and the repair is usually done same-day. If the post has heaved, we quote the post-reset separately and schedule it before reinstalling the opener.
Do you work on Ghost Controls and DoorKing openers in Kearny?
Yes, both. We service those and seven other automation brands, and we do not push a replacement when the existing motor is repairable. Call (928) 260-0864 for a written price before any work begins.
Gate Access Control in Kearny
Gate access control in Kearny is shaped by the two-family density: a side gate on a narrow alley passage often serves two or more households, and the entry system has to handle multiple codes, a phone line over a long driveway, or a keypad in direct weather exposure near the Passaic flood plain. Units mounted on steel gates along the industrial corridors get soaked, corroded, and salted until the keypad stops registering or the phone-entry relay fails. We see more corroded keypad terminals and failed power supplies in Kearny than almost anywhere else in the metro, because the hardware sits at gate level in humid, flood-prone air for years. See Gate Access Control for the complete breakdown.
Keypad Entry
Signs you need it
Some digits do not register, the keypad works intermittently after rain, or the backlight stays on and drains the power supply.
What it costs in Kearny
Keypad entry installation in Kearny typically runs $300 to $750 depending on whether we are tying into an existing opener or running new low-voltage line from the house.
How we do it
We mount the keypad in a weather-sealed housing, run or trace the low-voltage wiring, program the codes, and verify the relay fires the opener from the keypad before we leave.
Video Intercom
Signs you need it
You cannot see or talk to who is at the gate before releasing it, or the existing intercom handset in the house is dead and the outdoor station shows water inside the lens.
What it costs in Kearny
Video intercom installation in Kearny runs $850 to $2,400 for a single-gate system, with the spread driven by monitor count and whether we can reuse existing buried wire.
How we do it
We mount the outdoor station at gate level with a weather hood, run or verify the wire path, set up the indoor monitor, and test the release function from both ends.
What Gate Access Control Costs in Kearny
| Item | Typical range in Kearny |
|---|---|
| Keypad entry (installed) | $300 - $750 |
| Card reader system | $600 - $1,400 |
| Video intercom system | $850 - $2,400 |
Can you add a keypad to a gate that already has a remote?
Yes. We wire the keypad into the opener’s accessory input in parallel with the existing receiver, so both work independently. Most Kearny keypad add-ons are done in one visit with a written price before we start.
Does a video intercom need new wiring from the house to the gate?
Not always. If a working two-conductor or shielded wire is already buried, we reuse it. If it has corroded or was never run, we quote the new low-voltage run separately. Call (928) 260-0864 to get an exact price.
Gate Parts & Welding in Kearny
Gate parts and welding in Kearny is where the river and the road salt really show up: hinges rust through, steel posts snap at the base where standing water sat, and slide-gate rollers on industrial corridor properties grind flat against pitted track. The original wrought-iron and tubular-steel gates on the town’s two-family lots are often sound in the frame but failed at the connection points, which means a welded repair or a hardware swap restores the gate for far less than a full replacement. We carry gate rollers, hinges, and heavy-duty post stock, and we weld on site when the frame is sound enough to warrant it. For the full scope, see Gate Parts & Welding.
Hinge Replacement
Signs you need it
The gate drags on the latch side, the hinge pin is visibly worn or rusted through, or the gate has dropped enough that the opener struggles on the first few feet of travel.
What it costs in Kearny
Hinge replacement in Kearny runs $120 to $320 per gate depending on hinge count, gate weight, and whether we need to weld new plates onto the post.
How we do it
We support the gate with a jack, cut or unbolt the old hinges, weld or bolt new ones in place, and re-set the gate so it swings level without binding.
Post Replacement
Signs you need it
The post leans more than a degree or two out of plumb, the base shows rust-through or cracking, or the post has heaved out of its footing after a flood event.
What it costs in Kearny
Post replacement in Kearny generally runs $400 to $900 per post, including concrete removal, new footing, and re-hanging the gate, with the range set by post gauge and soil condition.
How we do it
We cut the old post at grade, break out the footing, set a new post in concrete sized for saturated soil, and re-mount the gate and opener to the new geometry.
What Gate Parts & Welding Costs in Kearny
| Item | Typical range in Kearny |
|---|---|
| Hinge replacement (per gate) | $120 - $320 |
| Post replacement (per post) | $400 - $900 |
| Custom welding repair | $150 - $600 |
Can you weld a broken gate frame on site in Kearny?
Yes, in most cases. If the break is in the frame and the surrounding steel is still sound, we weld it in place, grind the joint, and paint or prime it the same visit. If the frame is thin from rust, we quote a section replacement instead.
Do you carry gate rollers for slide gates in Kearny?
Yes. We stock common roller sizes for slide gates, including the heavy chain-link units common along Route 7 and the Belleville Turnpike corridor, and we replace worn rollers and pitted track together so the gate does not chew through a new set. Call (928) 260-0864 for an exact quote, free of charge.
Brands We Service in Kearny
We work on Ghost Controls, DoorKing, Elite, and Mighty Mule openers in Kearny, along with five other major automation brands. Common boards, remotes, and photo-eyes for these units are stocked on our trucks, which is why most motor and opener repairs in Kearny are single-visit. See our brands for the full list.
Pricing for Gate Repair in Kearny, NJ
| Service | Typical range in Kearny |
|---|---|
| Motor repair (capacitor, limit switch, gear) | $180 - $450 |
| Motor replacement | $650 - $1,500 |
| Complete opener system | $1,200 - $2,800 |
| Keypad entry (installed) | $300 - $750 |
| Card reader system | $600 - $1,400 |
| Video intercom system | $850 - $2,400 |
| Hinge replacement (per gate) | $120 - $320 |
| Post replacement (per post) | $400 - $900 |
| Custom welding repair | $150 - $600 |
What pushes a Kearny price toward the top of the range is almost always the same thing: a post that has heaved out of plumb after repeated flooding near the Passaic, or a frame too rusted from road salt to accept a weld. We quote the post or frame work as its own line item so you see exactly what you are paying for. Every price on this page is a written contract before any tool comes off the truck.
Neighborhoods We Serve in Kearny
We cover the full town, from the riverside flats near the Kearny Marsh up through the denser residential blocks off Kearny Avenue. Typical response time for gate repair calls in Kearny is same-day or next morning, including weekends.
- Kearny Marsh area and riverside flats
- Arlington section, near the North Arlington line
- South Kearny and the Belleville Turnpike corridor
- Central Kearny off Kearny Avenue
- Manor section, north of Route 7
Service Area - Cities Near Kearny
We also serve the neighboring towns where Kearny’s gate issues repeat themselves on slightly higher ground. See Belleville, NJ for flood-adjacent post work, East Orange, NJ for opener and access control on older housing stock, Bloomfield, NJ for similar two-family side-yard gate patterns, and Nutley, NJ for residential slide and swing gate service.
Serving Kearny, NJ - Our Local Coverage Area
We’re based in the Kearny area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Kearny
Same-day in most cases, and next morning at the latest for non-emergency calls. We dispatch technicians to Kearny daily, and a live person answers the phone 24/7, so you will never leave a voicemail when your gate will not open at 6 a.m.
For most repair work, no. If the project involves a new footing or a substantial structural change, Kearny may require a zoning or building permit, and we check that before we dig. We will tell you during the written estimate whether a permit applies to your job.
Yes. We give you a flat written price before any work begins, and that is the price you pay unless the scope changes and you approve the change in writing first. No surprise invoice at the end, on any Kearny job.
If your gate has stopped opening, is leaning out of plumb after a flood event, or the keypad will not take a code anymore, call (928) 260-0864. We will give you a written price, a documented photo record, and a 365-day promise that the repair stays done right. Serving Kearny from our New York City dispatch office, with crews on the ground locally every day.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Kearny Customers Say
"Good work on a long driveway gate. Arrived when they said, finished when they said."
- Sofia E."Honest about what did not need doing. Told me the operator had years left and only the control board needed replacing."
- Douglas N."Quoted in writing, installed on the day promised, and the price did not move. The crew was licensed and the number was on the paperwork."
- Wes A.