Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Revere
Gate repair in Revere usually costs between $145 and $620 depending on what failed. A seized hinge pin on a swing gate runs toward the lower end; a corroded post that needs to be cut out, re-set in concrete, and re-hung runs toward the higher end or beyond it. We work all over Revere, from the beachfront condos along Ocean Avenue to the triple-deckers off Broadway, and we carry marine-grade hardware on the truck because we know what the salt air on this side of the city does to iron. Call (928) 260-0864 and a live person answers, day or night.
Why Vance Gate Repair Is Revere’s Preferred Gate Repair Company
Our Gate Repair team has done thousands of jobs in coastal New England, and Revere presents a specific set of problems we don’t see five miles inland. Gates within a half-mile of Revere Beach Boulevard corrode faster here than anywhere else in the metro because the entire eastern edge of the city faces open ocean. That’s not a guess; it’s what the hinge pins show us when we pull them.
The work we do for Revere homeowners gets documented the way commercial access-control work gets documented: found-condition photos, part numbers, limit-switch readings, and a written price handed to you before we pick up a tool. That’s The Haven Standard, and it’s what Adrian Vance built the company around after years of doing access-control service on commercial sites starting in 2014.
Our dispatch is coordinated from the brand’s Boston office, and our crews serve Gate Repair in Revere locally, so response time is measured in hours, not days. You get a named, background-checked technician with a photo before arrival, not an anonymous truck.
Our Gate Repair Services in Revere
Hinge & Post Repair
This is the single most common repair we perform in Revere, and the reason is the same from Beachmont to Point of Pines: salt-laden air eats wrought iron and mild steel from the base up. A hinge post that looks solid at eye level is often thin as foil where it enters the concrete. We cut out the corroded section, set a galvanized replacement post in a footing raised above grade, and swap to stainless hinge hardware that actually survives this environment. Straightening the panel without addressing the post means the gate sags again within a season.
Weld & Rust Repair
On ornamental iron gates along Winthrop Avenue and the streets immediately behind Revere Beach, we routinely find the factory powder coat has failed within five to seven years. Owners assumed the coating was maintenance-free; the salt spray had other plans. We grind back the rust, weld in new pickets or frame sections, and finish with a marine-grade coating system. The panel gets a photo log of every repair, and you leave with the record.
Gate Realignment
When a gate binds against the driveway or won’t latch, it’s usually one of two things: a post that has moved, or a hinge that has worn oval. On low-lying parcels near Rumney Marsh and the beach flats, post footings get undermined by standing water and storm surge, and the gate starts to lean. We realign the leaf, shim or rebuild the hinge side, and reset the limit switches on automatic gates so the operator isn’t fighting a gate that no longer travels true.
Electric Gate Repair
For automatic and electric gates in Revere, salt air is as hard on the boards as it is on the steel. A control board in an operator box near the shore lives in a fog of salt every sea breeze. We test limit switches, photo-eyes, and board voltages, replace what’s dead, document the readings, and set travel so the operator doesn’t hammer itself against the same resistance twice a day.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterTrusted Brands We Service in Revere
We service nine gate-automation brands, so whatever is already on your property, one of our techs knows it. On Revere calls we regularly work on Viking, DoorKing, and Elite operators, and we don’t steer you toward a replacement motor when the one you have needs a board, a limit switch, or a capacitor. We keep common parts stocked locally for Revere customers, which means less waiting on a distributor when your beachfront gate won’t close.
Common Gate Repair Problems We See in Revere Homes
- Corroded hinge posts on beachfront gates. Salt spray from the ocean strips paint and powder coat years faster than inland, and the post rusts through at the base while the gate panel still looks straight. The fix is a galvanized post replacement, not another coat of paint.
- Shared-driveway gates between triple-deckers. Revere’s two- and three-family homes, most built between the 1920s and 1950s, often share a narrow side-yard gate between abutting properties. When one side stops maintaining the hinges, the gate seizes, and neither neighbor is sure who’s responsible. We fix the gate and document what was done so future disputes are short.
- Leaning posts on flood-zone parcels. Streets around Rumney Marsh and the low flats sit in FEMA flood zones where storm surge and standing water undermine gate post footings. The gate leans, then binds against the concrete, and straightening it without rebuilding the base just starts the cycle over. We set posts above the waterline.
- Factory powder coat failure on 2000s-era beachfront condos. Many of the ornamental gates put in during the beachfront building boom of the 2000s and 2010s have eaten through their coating in five to seven years. Marine-grade repainting and stainless hardware are the standard specification on virtually every call in that zone.
Pricing for Gate Repair in Revere, MA
A hinge pin replacement on a standard swing gate in Revere typically runs $145 to $260. Re-hanging a gate with new hinges and a realigned leaf runs $240 to $430. A corroded hinge post that must be cut out, replaced with galvanized steel, and re-set in concrete usually lands between $480 and $820 depending on the post diameter and whether the operator has to be re-leveled afterward. Weld-and-rust repair on an ornamental panel runs $280 to $560 per section. Electric gate board or limit-switch replacement runs $210 to $510 depending on the brand. Every price is written and handed to you before any work starts. That’s Clause 1 of The Haven Standard. If you have a written estimate from another company, bring it. We’ll review it at no cost and tell you where it’s honest and where it’s not.
Call (928) 260-0864 for a free estimate on gate repair in Revere. You’ll get a written price, not a ballpark.
We Also Serve Cities Near Revere
We handle gate repair across the North Shore metro, including Chelsea, Everett, Malden, and Saugus. If your gate is on a shared driveway in Everett or a hillside lot in Saugus, the same written-price, documented-record standard applies. Revere is one of the areas we cover most often because so much of the housing stock sits within a half-mile of salt water, but we’re on the road across the whole corridor.
Why does my gate rust so much faster in Revere than my friend’s gate in Malden?
Because Revere’s entire eastern boundary is open ocean along Revere Beach Boulevard, and the salt spray doesn’t stop at the beach. Malden sits inland and gets none of it. Within a half-mile of the shore, the air carries a fine salt mist year-round, and it gets into every hinge, bolt, weld, and post bottom. Malden gates rust over decades; Revere beachfront gates can lose a powder coat in five to seven years. The fix isn’t more paint; it’s galvanized posts, stainless hinges, and marine-grade coatings. Call (928) 260-0864 and we’ll quote the right specification, in writing, before we start.
My automatic gate near Revere Beach doesn’t always close. Is it the salt air?
It very often is. Salt air corrodes the limit switch contacts, the board connections, and the photo-eye housings on automatic gate operators near the shore, which produces intermittent faults: the gate stops mid-travel, reverses for no reason, or simply fails to close. We test the board, the switches, and the eye alignment, photograph every reading, and replace only what’s failed. On the streets immediately behind Revere Beach like Winthrop Avenue, we see this on nearly half of all service calls.
Why do gate posts lean after every storm on the low streets near Rumney Marsh?
Because the post footings are sitting in saturated ground that shifts with every storm surge and high water table. Parcels in the flats near Rumney Marsh and along the beach sit in FEMA flood zones, and the concrete base under a garden-variety gate post often sits below the waterline after heavy rain. The gate leans, then binds. The lasting repair is a deeper footing set above the standing-water line, with a galvanized post and drainage gravel around it. We do that work regularly in Revere, and it’s the only fix that doesn’t come back.
Our two-family shares a driveway gate with the neighbor. Who fixes the hinge post?
Legally, it depends on the deed and whether the gate is listed as a shared fixture, but practically, one side almost always ends up calling us because the gate has become inoperable. We fix the gate first and document what we found, what we replaced, and what the panel condition was before we started. With a written record in hand, Revere homeowners in shared-driveway situations have an easier conversation with the neighbor about splitting the cost. If the two sides want to split the invoice, we can prepare it that way. Call (928) 260-0864 and we’ll do a hinge-post inspection and give you the written price.
The powder coat on my beachfront gate is peeling after only five years. Can it be saved?
Yes, if the base metal hasn’t rusted through. Peeling powder coat on a gate near the beach is cosmetic until it isn’t; once moisture sits against the bare steel, section loss starts and pickets rust out from the inside. We grind the failed coating back, weld any thin sections, and refinish with a marine-grade system meant for salt exposure. On Winthrop Avenue we rebuilt a sagging swing gate at a 2010s beachfront condo where the post had rusted through at the base while the panel looked straight; the post was the failure, not the gate. We replaced it with galvanized steel set above the flood line, switched to stainless hinges and a marine-grade operator, and the gate has stayed true through two winters. Call (928) 260-0864 for a free estimate and a written scope before any work begins.
Serving Revere, MA - Our Local Coverage Area
We’re based in the Revere area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Contact Vance Gate Repair for Gate Repair in Revere
If your gate is sagging, seized, or refusing to close near the beach, call (928) 260-0864. You’ll speak to a live person, not a voicemail loop, and you’ll get a named technician, a written price, and a documented photo record of everything we find and fix. The estimate is free. The written price is yours before we pick up a tool.
Written by Adrian Vance, Owner at Vance Gate Repair, serving Revere since 2014.