Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Revere
Gate installation in Revere comes with a problem most contractors never mention: salt air eats standard hardware in three to five years. Within a half-mile of Revere Beach Boulevard, the marine layer settles on hinges, post bases, and operator arms daily. That’s why we specify stainless steel fasteners and marine-grade coatings on nearly every install we do here. You deserve a gate that doesn’t lean after two winters. Call (928) 260-0864 and we’ll give you a written price before we pick up a tool.
Key Takeaways
- Salt air behind Revere Beach corrodes powder-coated iron gates in 5-7 years; stainless hardware is the correct specification.
- Swing gate installation in Revere typically runs $2,400-$6,800; sliding gates run higher due to track and motor requirements.
- Revere’s three-deckers and shared driveways create unusual gate configurations that need site-specific measurement, not a catalog standard.
- We document every installation with a photo record and leave the wiring diagram with you. That’s the Haven Standard.
Why Vance Gate Repair Is Revere’s Preferred Gate Installation Company
Our crews know the streets behind Revere Beach. On Winthrop Avenue, we replaced a sagging double swing gate on a beachfront condo whose factory powder coat had failed in under six years. We set new stainless hinge posts in concrete above the waterline, swapped to galvanized rack and pinion operators with marine-grade keypads, and added safety photocells to meet UL 325. That’s a documented job with photographed evidence, not a guess. Homeowners in Revere call us because we show up knowing what coastal salt spray does to a gate before we even look at it.
We work across the Broadway corridor, Beachmont, and West Revere, and we understand how triple-decker driveways and shared access rights shape a gate install. Adrian Vance has run this company since 2014, and his team documents every job: what we found, what we set, what we installed. Revere customers get the same commercial-grade record-keeping on a residential driveway gate that commercial access-control sites demand. That standard applies to every Gate Installation we take on.
BeforeAfterOur Gate Installation Services in Revere
Swing Gate Installation
Swing gates are the most common gate type in Revere, and the salt air here is hard on them. The hinge posts rust at the base within 3-5 years, and the gate sags until it drags across the driveway. We install swing gates with galvanized post cores, stainless hinge hardware, and adjustable hinges so the gate can be re-leveled without cutting concrete. A typical single swing gate installation runs $2,400-$4,500, depending on width, material, and whether we’re replacing an existing post or setting new footings.
Double Gate Installation
Double gates show up often on Revere’s wider driveways and on shared access between triple-deckers. Two leaves mean two sets of hinges, two operators if automated, and a center stop you have to get right. Near the coast, the center point is where salt spray pools, so we spec stainless steel center stops and galvanized drop rods as standard. In the flood-zone sections near Rumney Marsh, we over-excavate post holes and set footings above the waterline. Double swing gate installation typically runs $4,800-$9,500.
Sliding Gate Installation
Sliding gates work well on narrow Revere side yards where a swing gate would block the sidewalk or street. They ride on a track or cantilever over a driveway. In Revere, track-mounted sliding gates need a concrete pad that drains, because standing water from coastal storms eats the track rollers faster than salt air does. We install cantilever systems where the driveway grade allows. A sliding gate installation runs $5,500-$12,000, depending on width, cantilever vs. track, and whether we run power.
Pedestrian Gate Installation
Pedestrian gates are what we install alongside a driveway gate when the homeowner wants daily foot access without opening the whole driveway. In Revere’s closely packed multi-family lots, a pedestrian gate off the front walk is often the smoother solution. These gates are usually 36-48 inches wide and can take the same marine-grade hardware spec we use on driveway gates. A pedestrian gate install runs $900-$2,200, including post setting and hardware.
For any of this work, we’ll provide a written quote before work begins. You get a flat price on paper, not a handshake estimate.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Revere
We work on whatever motor and gate hardware is already on your property, and we install new equipment without steering you toward a replacement you don’t need. That includes Mighty Mule, Ghost Controls, DoorKing, and Elite, among the nine major automation brands we service and install. For Revere customers, we keep stainless steel fasteners, marine-grade keypad housings, and zinc-plated brackets stocked because we know what the coastal air demands. If your gate runs on a brand we didn’t install, we’ll still service it and document the work under the same Haven Standard.
Common Gate Installation Problems We See in Revere Homes
- Rusted hinge posts at the base: Salt spray from Revere Beach settles at ground level, where water pools. The post rusts through 3-5 years after an inland-standard install. We see this weekly on Winthrop Avenue and Ocean Avenue. The fix is a stainless post core set in concrete above the waterline.
- Failed powder coat on wrought iron: Behind Revere Beach, factory powder coat on ornamental iron gates typically fails within 5-7 years. Pitting follows quickly. The correct spec is marine-grade two-part epoxy with UV-resistant topcoat, and factory powder coat is not a substitute.
- Leaning gates in flood-zone yards: Parcels near Rumney Marsh and the low flats behind the beach sit in FEMA flood zones. Undersized post footings heave and sink with freeze-thaw and storm surge. Re-setting the gate doesn’t fix it; the footing has to be rebuilt above the waterline.
- Shared driveway maintenance disputes: Revere’s abutting triple-decker lots often share one driveway gate. Two property owners, one gate, no clear maintenance agreement. Our written documentation, including the photo record and hardware spec sheet, gives both parties a clear record of what was installed and when it needs attention.
Pricing for Gate Installation in Revere, MA
Here’s what gate installation actually costs in Revere. A single wrought iron or steel swing gate install runs $2,400-$4,500. Double swing gates go $4,800-$9,500. Sliding gates run $5,500-$12,000 because of track, motor, and concrete work. Pedestrian gates are $900-$2,200. What moves the price: gate width, material (aluminum vs. steel vs. wrought iron versus wood), whether the existing posts and footings are sound, whether automation is involved, and whether the site is in a flood zone requiring deeper footings. Here’s the difference with Vance Gate Repair: the price we quote is the price on the invoice. Written scope, written price, before any tool touches the job. That’s Haven Standard Clause 1.
Call (928) 260-0864 for a free written estimate. We’ll come to Revere, measure the site, and hand you a number in writing.
We Also Serve Cities Near Revere
Our crews serve the immediate neighbors of Gate Installation in Revere across the metro’s North Shore edge: Chelsea, Everett, Malden, and Saugus. The same salt-air spec we apply behind Revere Beach gets adjusted for each city’s housing stock and lot geometry. If you’re on the Revere line, you’re in our service area.
Serving Revere, MA - Our Local Coverage Area
We’re based in the Revere area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Revere
Yes. Within a half-mile of Revere Beach Boulevard, stainless steel hinges, galvanized post cores, and marine-grade coatings are the default spec, not an upgrade. Standard zinc-plated hardware fails in 3-5 years here. Stainless steel lasts decades. Inland cities like Chelsea or Everett don’t face the same constant salt deposition, so the same hardware is fine there. If you’re within a half-mile of the water, pay for stainless. It’s cheaper than replacing the gate in four years. Call (928) 260-0864 for a written quote on marine-spec hardware.
Factory powder coat on ornamental iron gates fails in 5-7 years behind Revere Beach because salt-laden air pits the steel underneath, lifting the coating from inside. The coating itself isn’t defective; the environmental load is. The correct fix is a marine-grade two-part epoxy primer with a UV-stable topcoat, applied after proper surface prep. We’ve documented this exact failure on Winthrop Avenue repeatedly. We can re-coat and re-hang a gate that’s still structurally sound, and we’ll put the recoating spec in writing before the work starts.
You can, but most solar opener kits are engineered for single gates that get direct sun most of the day. In the Rumney Marsh area and low-lying sections of Revere, winter sun angles and frequent cloud cover mean many double swing gates won’t charge enough to stay reliable. We don’t recommend solar power as the primary source for double gates here. A hardwired 12V or 24V system with battery backup is more reliable. We’ll quote both options in writing and show you the power requirement before any install starts.
The gate sags because the hinge post isn’t strong enough for daily cycling by multiple families, or because the post base was set in undersized concrete and has shifted. The fix is a larger-footing post with an adjustable hinge, plus a center stop to hold both leaves straight. For shared driveways between abutting triple-deckers, we document the condition of both posts and the installed hardware so there’s a record for both property owners. A typical shared-driveway gate repair with new posts and adjustable hinges runs $1,800-$3,400, depending on post condition and gate width.
Yes. Under UL 325 safety standards, any automatic gate installed in Revere must include entrapment protection: photo-eye sensors across the gate path, a reversing edge, and a control board that monitors them. This is a safety requirement, not an option. We wire every automatic gate installation with two independent safety devices and test them before we leave. We’ll show you the photo-eye alignment and the reversing-edge test reading. Call (928) 260-0864 for a quote that includes entrapment protection, in writing, on your own site.
Written by Adrian Vance, Owner at Vance Gate Repair, serving Revere since 2014.
Ready for a gate install in Revere that won’t rust out in five years? Call (928) 260-0864 for a free, written estimate. We answer the phone 24/7, and you’ll get a flat price before any work begins.
Gate Installation in Nearby Areas
