Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Chandler
A new driveway gate in Chandler runs between $3,800 and $9,500 for most single-family homes, with pedestrian gates starting around $1,200 and full security gate packages with operators landing in the $7,000-$14,000 range depending on material and automation. We give you that price in writing before any work starts, not after. If you’re in Chandler and the gate that came with your 1990s-era home is finally at the end of its life, call (928) 260-0864 and we’ll bring a tape measure, not a sales pitch.
We know Chandler’s gates because we’ve been inside thousands of them since Adrian Vance started this company in 2014. The Ocotillo courtyards, the Fulton Ranch driveways, the gated entries off McQueen Road and Cooper Road. The same steel, the same caliche, the same monsoon dust. That local knowledge is what keeps your installation from becoming a six-month callback.
Why Vance Gate Repair Is Chandler’s Preferred Gate Installation Company
Chandler homeowners call us after they’ve done the research. They’ve read the three-star reviews on other gate companies, and they’ve learned the hard way that a verbal estimate means nothing when the invoice shows up. We operate differently. Every installation starts with a written scope and a written price, handed to you before a single tool comes off the truck. That’s Haven Standard Clause 1, and we’ve followed it on all 22,000+ gate jobs since 2014.
Our technicians show up in uniform, background-checked, with a name and photo sent to you before arrival. They document everything: the condition of the existing post footing, the wire pull, the limit switch settings on the new operator, the part numbers installed. You get that photo record when the job is done. No other Gate Installation in Chandler company we know of leaves a documented evidence trail like that on a residential property.
Response time to Chandler is typically same-day for repair emergencies and within a few days for scheduled installations. A live person answers our phone 24 hours a day, every day. When your gate fails at 6 a.m. on a Monday and you can’t get your car out, that matters.
Our Gate Installation Services in Chandler
Driveway Gate Installation
Most Chandler driveway gates we install are single-swing or sliding designs in powder-coated steel or wrought iron, matched to the Spanish Colonial or Southwestern lines of the house. A standard single-swing driveway gate with a Ghost Controls or Viking operator runs $4,200-$7,800 in Chandler, including the post, operator, safety photocells, and programming. Double gates cost more, as do custom wrought-iron designs from shops that serve the Ocotillo and Fulton Ranch HOA requirements.
Pedestrian Gate Installation
Pedestrian gates in Chandler are frequently tied to pool enclosures, and Arizona’s pool-barrier statute (ARS §36-1681) is not optional. The gate has to close on its own and latch on its own, every time. We install self-closing hinges and spring latches on pool gates across Chandler for $1,200-$2,800 with a basic steel frame, or more for ornamental iron matched to the driveway gate. We check the closure force and latch throw before we leave, and we photograph the settings.
Sliding Gate Installation
Cantilever sliding gates fit Chandler’s larger properties, especially on the wider lots east of Arizona Avenue. A motorized sliding gate in the Chandler area runs $6,000-$11,000 installed, depending on length and whether we’re trenching new conduit for power. That conduit detail matters here. In the late-1990s developments, original conduit was trenched through caliche, and irrigation overspray from HOA landscaping has been seeping into those runs for two decades. We check the wire pull before we quote, because swapping a board into a corroded conduit is a temporary fix, not an installation.
Swing Gate Installation
Swing gates are the default in Chandler’s 1990s master-planned communities, and they’re the ones now failing at the highest rate. Exposed summer concrete hits 150°F regularly, and the aluminum frames on those original gates expand, rack out of plumb, and pull hinge posts out of alignment. A new swing gate with a properly footed post, an operator rated for the gate’s weight, and monitored safety edges runs $4,000-$8,500 for most Chandler homes. The price depends on post condition and whether we need to re-pour a footing.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterTrusted Brands We Service in Chandler
We install and service nine major automation brands, and for Chandler specifically we keep common parts for Viking, Ghost Controls, and DoorKing on the truck. That means less waiting on freight and fewer second trips. If your existing operator still works and you’re only replacing the gate itself, we can keep it. If the operator is obsolete and parts are gone, we’ll tell you straight, with a written quote for a Ghost Controls or Elite unit that fits the new gate. We keep the Gate Installation process simple: the price includes the operator, the safety devices, the programming, and the documentation we hand you at the end.
Common Gate Installation Problems We See in Chandler Homes
- Original 1990s operators on their third or fourth control board. These boards die from heat and dust, and at some point the honest answer is to replace the operator rather than feed it another $400 board. We price both options and let you decide with real numbers.
- Hinge posts racked out of plumb from thermal expansion. Chandler’s summer ground heat expands aluminum gate frames, and over 20 years that slowly pulls posts out of vertical. A new gate hung on a bad post wears out its operator fast. We fix the footing before we hang the gate.
- Monsoon haboob dust packed into motor housings and limit switches. July through September, the dust storms push fine particulates into every opening. Sealed housings help, but most residential operators aren’t sealed well. We recommend a pre-monsoon service call in May or June, and we build that into the install conversation.
- Conduit runs corroded by HOA irrigation overspray. This is the one that gets expensive if missed. In Ocotillo and Fulton Ranch, irrigation lines run near original gate conduit, and mineral scale inside the conduit turns a $900 operator swap into a $2,500 wire pull and conduit replacement. We scope the conduit before we quote, so the written price already includes what we found.
Pricing for Gate Installation in Chandler, AZ
Here are the numbers we quoted on real Chandler jobs in the last 12 months:
- Pedestrian pool gate, steel frame, self-closing hinges: $1,200-$2,800
- Single-swing driveway gate, steel or aluminum, no operator: $2,500-$4,500
- Single-swing driveway gate with Ghost Controls or Viking operator, safety photocells: $4,200-$7,800
- Double-swing driveway gate with operator: $6,500-$11,000
- Sliding gate with operator, new conduit run: $6,000-$11,000
- Security gate package with access control keypad and exit loop: $7,000-$14,000
The range depends on post condition, existing conduit, gate material and size, and whether the old operator can be reused. Every quote is written, itemized, and handed to you before any work begins. Call (928) 260-0864 for a free estimate, and if you already have a written estimate from another company, we’ll review it at no charge.
We Also Serve Cities Near Chandler
Our crews cover Chandler and the surrounding East Valley, including Gilbert, Tempe, Mesa, and Scottsdale. If you’re in any of those cities and need a gate installed or replaced, the same written-price standard applies. One call to (928) 260-0864 covers the whole area.
Serving Chandler, AZ - Our Local Coverage Area
We’re based in the Chandler area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Chandler
Chandler’s master-planned boom in the 1990s and early 2000s built thousands of gates in Ocotillo, Fulton Ranch, and similar communities within roughly the same decade, using the same era of operators and the same powder-coated steel. Those components were never designed to last 25+ years in this climate, so hinge wear, board failures, and post fatigue are now showing up in waves across whole subdivisions. Replacement is often cheaper than repeated repairs, and we’ll show you the math in writing. Call (928) 260-0864 for an exact quote on your specific gate.
Yes. ARS §36-1681 requires pool enclosure gates to be self-closing and self-latching, opening outward from the pool, and in good repair. Chandler’s high pool-per-household rate means we do a steady stream of pool gate compliance installations and adjustments. If your gate no longer closes on its own or the latch doesn’t catch, you’re out of compliance, and we can fix it. Call (928) 260-0864 and we’ll bring the current code requirements with us.
Yes, in most cases. Any modern operator we install in Chandler includes monitored safety photocells, and we can often add them to an existing operator if the control board supports it. On a 1990s LiftMaster or Linear board, the answer is sometimes no, and at that point we’ll give you a written quote for a retrofitable operator. Call (928) 260-0864 and we’ll tell you what your existing system can and can’t do.
Haboob dust in July through September is fine enough to enter motor housings, limit switches, and control boards. It coats contacts, scores limit-switch tracks, and clogs the photo-eye lenses. We recommend a pre-monsoon service call in late May or June in Chandler to clean and seal what can be sealed, and to photograph the limit settings so you have a record. Call (928) 260-0864 to schedule before the dust hits.
If the panel itself is still straight and the hinges and post are solid, re-shimming and adjusting costs $250-$500. If the post has racked out of plumb or the panel frame is twisted from years of thermal cycling, replacement usually lands between $2,500 and $6,000 for a typical Chandler driveway gate. We’ll measure the deflection and give you a written price for both paths, no pressure. Call (928) 260-0864 for a straight answer.
If your Chandler gate is old, sagging, or failing after every monsoon, the answer is a documented installation with a written price you saw before we started. Call (928) 260-0864 for a free estimate. We’ll measure, we’ll inspect the conduit and the posts, and we’ll hand you a written scope and a flat price. That’s the only way we work.
Written by Adrian Vance, Owner at Vance Gate Repair, serving Chandler, AZ since 2014.