Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Farragut, TN
Gate motor and opener failures are the most common call we get from Farragut homeowners, and the pattern is consistent: a LiftMaster or Viking operator that worked fine through the summer seizes up after the first hard ice storm, or a Ghost Controls swing arm loses its limit setting and starts banging the gate against the post. These are not mysteries to us. Farragut’s mix of mid-1980s through 2000s planned subdivisions, decorative steel driveway gates, and HOA architectural requirements means most repairs here need a written paper trail and a brand-specific parts source, not a generic swap. Call (928) 260-0864 and a live person answers, any hour.
Why Farragut Homes Are Different
Farragut has an unusually high density of HOA-governed upscale subdivisions, and many of those communities run active architectural review boards that must pre-approve any visible gate component before it gets installed. That means a hinge replacement, a new keypad housing, or a welded scroll repair often cannot proceed until the board has seen photos, part numbers, or a sample finish. We handle that paperwork as part of the job. It also means a technician cannot pull any generic replacement panel off the truck and bolt it on; in several of the older established subdivisions near the Fox Den area, the HOA requires replacement gate panels to reproduce the original decorative scroll pattern exactly, which forces either custom fabrication or tracking down the original manufacturer. Aesthetic conformity is enforced by both the HOA bylaws and Farragut’s own municipal appearance standards, so gate repair here is materially more documentation-heavy than in surrounding Knox County communities.
Weather compounds the problem. East Tennessee’s periodic winter ice storms deposit glaze ice that bends decorative gate arms, seizes opener mechanisms, and cracks welds on ornamental ironwork. Farragut takes that harder than the urban Knoxville core because of elevation and exposure on larger lots. And year-round valley humidity accelerates rust anywhere a powder-coat finish has been chipped. That combination of HOA oversight and real weather damage is why a written price, a documented photo record, and a named technician on the way matter more here than in any nearby community. Dispatch for Farragut is coordinated from our Memphis office, with local crews serving the area directly.
Our Main Farragut Services
Most Farragut homeowners reach us first for one of two reasons: a gate that has stopped opening or a gate that needs to be installed or replaced to meet HOA standards. Both are covered below, each with its own dedicated Farragut page.
Gate Repair in Farragut
Repair work in Farragut typically means diagnosing a swing or slide gate that has stopped, drifted past its limit, or started making a noise it never made before. The local twist is the HOA layer: if a visible component needs to be swapped out, the architectural review board may need to see the replacement part before we install it. We photograph what we find, write the price down, and do the job to match the original ironwork or opener configuration. When the HOA needs documentation, we hand you the photo log and the written record before we leave. Gate Repair in Farragut has the full detail on common failures and response times.
Gate Installation in Farragut
New gate installation in Farragut almost always starts with the HOA or architectural review board. Most neighborhoods here require pre-approval on the gate’s material, finish, height, and scroll pattern before anything gets ordered or set in concrete. We prepare submittal-ready photos and specifications, source posts and panels that match the subdivision’s original look, and document the entire install from the first hole to the final limit setting. Automation is included where the homeowner wants it, and every brand we install has its wiring diagram and setup readings photographed and left with you. Gate Installation in Farragut covers what the process looks like in Farragut specifically.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Motor & Opener in Farragut
Gate motor and opener work is the backbone of what we do in Farragut. The housing stock here, large brick and stone-fronted homes built in planned subdivisions from the mid-1980s through the 2000s, means automated driveway gates are unusually common compared to neighboring Lenoir City or west Knoxville, and most of those operators are ten to twenty-five years old now. Ice storms seize older motors, and the same humid air that rusts ornamental ironwork corrodes limit switches and control board contacts. This service covers motor installation, motor repair, linear or slide motor work, and intercom integration, and you can read the broader Gate Motor & Opener hub for more detail.
Motor Installation
Signs you need it
The existing motor is dead, beyond economical repair, or the homeowner is switching from a manual gate to automation and needs the whole operator set installed.
What it costs in Farragut
Motor installation in Farragut typically runs $800 to $2,400 depending on whether the operator is a slide motor, a linear arm, or a full underground or ram-style unit requiring concrete work.
How we do it
We mount the operator, set the travel limits, wire the safety edges and photo-eyes, photograph every connection, and hand you a written record of the part number and settings before we leave.
Motor Repair
Signs you need it
The gate opens partway, reverses for no visible reason, hums without moving, or trips a breaker repeatedly.
What it costs in Farragut
Motor repair runs $150 to $800 in Farragut depending on whether we are replacing a capacitor, a limit switch, a control board, or a stripped gear set inside the unit.
How we do it
We test the motor under load, identify the failed component, write the repair price before we touch a tool, and photograph the replacement part and the final test cycle.
What Gate Motor & Opener Costs in Farragut
| Item | Typical range in Farragut |
|---|---|
| Motor installation | $800 - $2,400 |
| Motor repair | $150 - $800 |
| Control board replacement | $300 - $700 |
Can you repair my LiftMaster opener the same day I call?
In most Farragut cases, yes. We carry common LiftMaster, FAAC, BFT, and Linear boards, capacitors, and limit switches on local trucks, so a single-component motor repair is often completed on the first visit. Call (928) 260-0864 for a real answer from a live person.
Do you work on Viking and Ghost Controls operators?
Yes. We service Viking, Ghost Controls, DoorKing, and Elite, along with five other major automation brands, so the motor already on your Farragut property does not have to be replaced just because it is not the brand another company stocks.
Gate Access Control in Farragut
Gate access control in Farragut usually means adding or repairing the entry method: keypad, remote, phone entry, card reader, or video intercom on an existing automated gate. Because Farragut’s subdivisions run on HOA aesthetic standards, the hardware has to be mounted where the board approved it or where it stays visually discreet, and we handle that instead of leaving you to manage it. This page covers what we do; the broader Gate Access Control hub has the full system detail.
Keypad Entry
Signs you need it
The keypad is cracked, waterlogged, unlit, or no longer accepts codes, or the homeowner wants a new code set up and an old one permanently deleted.
What it costs in Farragut
Keypad entry repair or replacement in Farragut typically runs $200 to $600 depending on whether we replace the keypad, the controller board, or the wiring run back to the motor.
How we do it
We test the keypad signal at the controller, replace the bad unit or wire, program new codes in front of you, and photograph the installed hardware and its mounting position.
Remote Control
Signs you need it
The opener only works from the wall button, the remote range has shrunk to a few feet, or a new homeowner needs the previous owner’s remotes cleared from memory.
What it costs in Farragut
Remote control work in Farragut runs $100 to $350, covering receiver replacement, antenna relocation, or a full reprogramming and code-clearing session.
How we do it
We identify the receiver frequency, clear the old codes, pair the new remotes, and document the process so any future remote can be added without starting over.
What Gate Access Control Costs in Farragut
| Item | Typical range in Farragut |
|---|---|
| Keypad entry | $200 - $600 |
| Remote control | $100 - $350 |
| Video intercom or phone entry | $450 - $1,400 |
Can you add a keypad to a gate that currently only has a remote?
In most Farragut cases, yes. We tap the existing controller input or add a receiver module, mount the keypad in an HOA-acceptable position, and wire it back clean. The written price is handed over before the work starts.
Will HOA approval be needed for a video intercom?
Often yes in Farragut, because a visible intercom panel changes the appearance of the gate post. We provide photos and mounting specifications for the architectural review board and can submit them on your behalf when that helps move the approval along.
Gate Parts & Welding in Farragut
Ornamental driveway gates in Farragut take structural abuse from ice and rust that the openers cannot protect, which means hinge replacement, post repair, rail straightening, and custom welding are routine jobs here. Ice storms bend the decorative arms, and once the powder-coat is cracked, valley humidity keeps the rust moving. On older Fox Den area properties especially, replacement panels often have to be custom-fabricated to match original scroll patterns, because the HOA will not accept a generic substitute. Full details live on the Gate Parts & Welding hub.
Hinge Replacement
Signs you need it
The gate sags, drags on the ground at the latch side, or the hinge pin has worn enough that the gate visibly shifts when pushed.
What it costs in Farragut
Hinge replacement in Farragut runs $250 to $900 per gate depending on how many hinges are replaced, the weight of the gate, and whether the post face needs to be re-plated or re-drilled.
How we do it
We support the gate safely, remove the old hinges, weld or bolt the new set to match the original powder-coat finish, and photograph the gate hanging level before we leave.
Post Replacement
Signs you need it
The gate post is leaning, the concrete around the base is cracked, or the post has rusted through at ground level and no longer holds the gate square.
What it costs in Farragut
Post replacement in Farragut is a heavier job and runs $800 to $2,800 depending on whether the post is a simple square steel upright, a brick column that must be reconstructed, or a decorative stone pillar needing matched material.
How we do it
We remove the old post or column, pour a proper footing, set the replacement in concrete, and wait for the specified cure before re-hanging the gate and resetting the opener limits.
What Gate Parts & Welding Costs in Farragut
| Item | Typical range in Farragut |
|---|---|
| Hinge replacement | $250 - $900 |
| Post replacement | $800 - $2,800 |
| Custom welding or scroll repair | $150 - $700 |
Can you match the original decorative scroll pattern for the HOA?
Yes. Where the original manufacturer is gone or unknown, we fabricate replacement pieces to match the existing scroll pattern and powder-coat them before welding them in. We document it with photos for the architectural review board.
Do you do small welding repairs or only full gate work?
We do small repairs: a cracked picket, a broken finial, a stress crack at a hinge plate or a rail joint. The written price covers the specific weld, the grind-back, and the spot finish.
Brands We Service in Farragut
We service Viking, Ghost Controls, DoorKing, and Elite operators, along with five other major automation brands. Trucks running Farragut jobs carry common replacement boards and parts for these brands, which keeps most single-component repairs to one visit. See our brands for the full list.
Pricing for Gate Repair in Farragut, TN
| Service | Typical range in Farragut |
|---|---|
| Motor installation | $800 - $2,400 |
| Motor repair | $150 - $800 |
| Keypad entry | $200 - $600 |
| Remote control | $100 - $350 |
| Video intercom or phone entry | $450 - $1,400 |
| Hinge replacement | $250 - $900 |
| Post replacement | $800 - $2,800 |
| Custom welding or scroll repair | $150 - $700 |
What pushes a Farragut quote toward the top of these ranges: custom fabrication to match an HOA scroll pattern, heavier ornamental steel gates, and post work that requires matching brick or stone. Every Farragut job gets a written price before any work starts, under The Haven Standard, so the number we hand you is the number you pay.
Neighborhoods We Serve in Farragut
We work throughout Farragut, including the established subdivisions and newer planned communities where automated driveway gates are common. Typical response time for a Farragut gate repair is same day or next morning, depending on the failure and part availability.
- Fox Den
- Concord Hills
- Village Green
- Farragut Commons
- Saddle Ridge
Service Area - Cities Near Farragut
Beyond Farragut, our Tennessee crews cover the surrounding metro and region. Homeowners in Knoxville, TN call us for the same written-price, documented-work standard, and we regularly cross into Memphis, TN and New South Memphis, TN for larger installations and access-control work. Nashville, TN is also in our wider service area for scheduled projects.
Serving Farragut, TN - Our Local Coverage Area
We’re based in the Farragut area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Farragut
For most mechanical repairs like motor, limit switch, or remote work, no. For any visible component change, such as a hinge, panel, post, keypad, or intercom, many Farragut HOAs do require pre-approval. We provide documentation to the board and can help move that along.
Emergency gate failures are typically reached same day, and most non-emergency Farragut repairs are scheduled within one to two days. A live person answers at (928) 260-0864, any hour, so you are not leaving a message and waiting for a call back.
We serve all of Farragut, including Fox Den, Concord Hills, Village Green, Farragut Commons, and outlying subdivisions. Dispatch is coordinated from our Memphis office, and local crews handle the full Farragut area. Estimates are free and always written.
Call (928) 260-0864 for a free estimate on any gate repair in Farragut. A live person answers, the price is in writing before we start, and you get a documented photo record of everything we find and fix. That is the standard on every Farragut job, no exceptions.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Farragut Customers Say
"Our gate was hit by a delivery truck. They came out, documented the damage properly for the insurer, and the claim went through without an argument."
- Camille R."Good work on a long driveway gate. Arrived when they said, finished when they said."
- Sofia E."Honest about what did not need doing. Told me the operator had years left and only the control board needed replacing."
- Douglas N.