Gate Repair in Tucker - Fixed Today, No Surprise Invoice

Gate Repair in Tucker, GA

Gate motor and opener failure is the most common repair call we handle in Tucker, GA. The neighborhoods here, built mostly between the late 1950s and the 1980s on Georgia red clay, produce a specific pattern: a gate worked fine for 30 years, then one summer storm season it starts grinding, reversing, or refusing to open at all. In Tucker, that pattern usually traces to a motor straining against a post that has crept out of alignment, or a control board that has been cooking in a metal box through years of DeKalb County heat and humidity. Call (928) 260-0864 and we’ll put a written price in front of you before any work starts.

Call (928) 260-0864

Why Tucker Homes Are Different

Most of Tucker’s housing stock went in before the city incorporated in 2016, which has a real effect on gate work. Swing gates set in the 1970s and 80s were often set directly into red clay with a shallow concrete pad and no gravel drainage bed. That clay wicks moisture through the wet winters, dries and contracts through the hot summers, and the post starts to rock. The gate still opens on the phone, but when we put a level on it the post is out by enough that the hinges are carrying load they were never designed for. On top of that, Tucker’s mature hardwood canopy, especially through established neighborhoods like Idlewood and Tucker-Northlake, drops limbs and pushes roots into post footings. After a heavy summer thunderstorm line, we often find a swing gate that failed not because the motor quit, but because a post moved and the motor burned itself out trying to push a gate that no longer swings true. Many of these installations predate the city’s permitting structure entirely, so repair calls frequently surface gates that were never set to any code at all.

Our Main Tucker Services

The two calls we take most often in Tucker are full-service repairs and complete installation work, and each has its own page with local detail.

Gate Repair in Tucker

This covers broken hinges, sagging swing gates, failed slide-gate rollers, damaged posts, and gate sections that have been hit by a car or a falling limb. Tucker’s red clay post problems and tree-root pressure make hinge misalignment the most common repair diagnosis, not motor failure. We document what we find with photos, write the scope, and hand you the price before work begins. See Gate Repair in Tucker for detail.

Gate Installation in Tucker

New gate installations in Tucker need to account for that same red clay: we set posts deeper than the old standard and install a gravel drainage bed so the footing doesn’t rock the same way a 1970s pad does. We also work around mature root systems without cutting through a hardwood’s anchor roots. The full scope is on Gate Installation in Tucker.

Before

After

Gate Motor & Opener in Tucker

Gate motor failures in Tucker are rarely just motor failures. The swing gate arms and slide-gate motors installed across Tucker’s 1960s-to-1980s neighborhoods are often still working against posts that have shifted in the red clay, and the motor takes the abuse until a control board, capacitor, or gear set finally gives way. In the thick summer thunderstorm season, a power surge through a DeKalb County line takes out the control board just as often as time does. Our Gate Motor & Opener work covers the full range from motor replacement to limit-switch tuning, and we service what is already on the property rather than steering you toward a replacement you may not need.

Motor Installation

Signs you need it

The motor hums but nothing moves, or it trips its breaker on start-up and smokes from the housing.

What it costs in Tucker

Motor replacement in Tucker typically runs $450-$1,100 depending on brand and whether the mounting bracket is reusable.

How we do it

We remove the failed motor, photograph the existing bracket and wiring, install the new motor to the same or corrected mount, set and record the limit positions, and leave you a written photo log before we go.

Motor Repair

Signs you need it

The gate stops partway, reverses without command, or runs fine one day and locks up the next.

What it costs in Tucker

Motor repair in Tucker ranges $180-$400 for most capacitor, gear, and limit-switch corrections.

How we do it

We open the motor housing, test the capacitor and gear set under load, name what we found, replace only what failed, then photograph the final wiring and settings for the job record.

What Gate Motor & Opener Costs in Tucker

Can you replace a gate motor without replacing the gate?

Yes. In most Tucker homes the gate itself is still sound; only the motor or its board has failed. We swap the motor onto the existing gate and reuse the rail or arm if it is straight.

Why did my gate motor fail after a storm?

Tucker’s summer thunderstorm lines bring surge events through DeKalb County power. Control boards with no surge protection take the hit first. We can add inline surge protection during any motor repair; call (928) 260-0864 for a written quote before work begins.

Gate Access Control in Tucker

Access control in Tucker tends to come up when a homeowner wants to stop relying on a physical keypad on a post, or when that keypad has been failing for months and the gate is left standing open. Tucker’s older gates often have a single hardwired keypad that has been outside in the elements since before the city incorporated; the faceplate cracks, water gets in, and codes stop registering. Our Gate Access Control work covers keypads, remotes, phone entry, card readers, and video intercoms, always with the written price before the work begins.

Keypad Entry

Signs you need it

Some digits on the keypad work intermittently, or the keypad is cracked and water is visible under the faceplate.

What it costs in Tucker

Keypad replacement or repair in Tucker generally runs $150-$420 depending on wiring and whether the controller is still good.

How we do it

We meter the existing keypad wiring, mount the new or repaired unit, program your codes, and hand you a written list of the codes and the photo record.

Remote Control

Signs you need it

The remote works only from inches away, or a visitor’s remote will not take a code while yours still does.

What it costs in Tucker

Remote control programming or receiver replacement in Tucker costs $85-$250 in most cases.

How we do it

We check the receiver frequency against the remote, clear stale codes, re-program the buttons, and photograph the receiver board with the new settings.

What Gate Access Control Costs in Tucker

Can I control my Tucker gate from my phone?

Yes. We install phone-entry bridges that connect your gate operator to your cellular network, so you open the gate from anywhere. The written price covers the hardware, the wiring, and the programming before we start installing anything.

Do you service existing access control from another installer?

Yes. We work on what is already on the property, including DoorKing, FAAC, and BFT controllers. Bring any paperwork from the original install and we will match the replacement part by model, not guess. Call (928) 260-0864 for a free written estimate.

Gate Parts & Welding in Tucker

Gate parts and welding calls in Tucker are usually about a hinge that has torn out of a post, or a slide-gate rail that has bent after a car clipped it. In Tucker’s older neighborhoods, the real work is often at the post, not the hinge: the post has rocked in the red clay for so long that the hinge bolts have wallowed out the holes. Our Gate Parts & Welding work covers hinge replacement, post setting, rail repair, custom welding, and roller replacement, with a written price before we touch a tool.

Hinge Replacement

Signs you need it

The gate drops at the latch end, scrapes the driveway, or shows a gap at the top hinge when closed.

What it costs in Tucker

Hinge replacement in Tucker typically runs $95-$240 per hinge, plus post work if the post has moved.

How we do it

We cut out the failed hinge, weld or bolt in the replacement, true the gate to the post, and photograph the finished weld and the gate’s level line.

Post Replacement

Signs you need it

The gate still swings but the post visibly leans, or the concrete pad around the post is cracked and pulling away.

What it costs in Tucker

Post replacement in Tucker runs $300-$700 per post, including the new concrete and gravel drainage bed.

How we do it

We dig out the old pad, set a new post in concrete over a gravel drainage layer so the red clay stops wicking water, and photograph the depth before backfill.

What Gate Parts & Welding Costs in Tucker

Can you weld a gate that is still on the property?

Yes. We weld in place when the surrounding material is sound. If the post is moving, we reset the post first, then weld the hinge or bracket. Call (928) 260-0864 for an exact written quote.

Why does my gate keep sagging after hinge repair?

In Tucker the post is usually the problem, not the hinge. A hinge replaced on a rocking post will sag again. We check the post with a level before we sell you a hinge, and show you the photo evidence.

Brands We Service in Tucker

We stock parts and service motors from BFT, Linear, Viking, and Ghost Controls, among the nine major brands we cover. Most common control boards and remotes are available same-week in Tucker, not special-ordered from a distributor. See our brands for the full list.

Pricing for Gate Repair in Tucker, GA

Neighborhoods We Serve in Tucker

We cover all of Tucker, GA and usually reach most neighborhoods within 60-90 minutes of your call. The list below is not exhaustive; if you are in Tucker, we are close.

• Idlewood
• Tucker-Northlake
• Historic Downtown Tucker
• Brittany Woods
• Browning Estates

Service Area - Cities Near Tucker

We also handle gate repair in the communities around Tucker. If you are just outside the city line, we can often reach you as quickly as we reach north Tucker. See Decatur, GA, Lawrenceville, GA, Redan, GA, or Duluth, GA for local detail.

FAQs About Gate Repair in Tucker