Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Boston, MA
Gate motor and opener work in Boston starts with one fact: most of the gates in this city hang on iron or steel set into brick and granite that predates the automobile. When a motor strains, a hinge binds, or a post leans, the cause is usually the ground it’s set in, not just the part that failed. We repair and replace gate motors, access control, and welded ironwork across Boston, and every job is priced in writing before any tool is picked up. Call (928) 260-0864 for a free estimate.
Why Boston Homes Are Different
Boston’s housing stock is heavily pre-1940: Federal and Victorian brick rowhouses, triple-deckers, and Italianate brownstones. Original wrought-iron gates hung on hand-laid granite or brick pillars from the 1800s are common in Beacon Hill, Back Bay, and the South End. That means welded restoration of period hardware, rather than panel swaps, is the standard approach here. A gate that looks like the problem often isn’t. Decades of frost heave tilt the original brick or granite pillar several degrees, and until that post lean is addressed, no hinge adjustment holds through another winter.
The climate compounds it. Boston’s frost line runs roughly 48 inches deep, and the city applies heavy road salt through long winters. Posts heave out of plumb from freeze-thaw ground movement. Chloride-laden air from the harbor and salt spray from treated streets accelerate deep pitting rust even on gates that appear intact. A motor that worked in October can be fighting a twisted frame by February. We account for that from the first estimate, not after the second callback.
Our Main Boston Services
Most Boston homeowners reach out for one of two reasons: an existing gate has stopped working, or they want a new gate built and hung on old stone. Both jobs in this city share the same constraint: the pillars are original, the preservation district rules are real, and the work has to match what was there before.
Gate Repair in Boston
Repair in Boston usually means restoring what’s already on the property rather than swapping in modern panels. Hinges welded to 1890s pickets, latch bars bent out of true, wheels worn into flat spots from decades of rolling on brick pavers. In Beacon Hill and the South End, the Landmark Commission may require matching period materials and design for any significant alteration. We document what we find, weld in place where possible, and leave a photo record of every adjustment. Gate Repair in Boston covers the full scope of this work.
Gate Installation in Boston
New gates in Boston are measured against the opening as it actually stands, not the blueprint. Pilasters in Charlestown brownstones are rarely plumb, and the gate has to be built to the lean or the pillar has to be reset first. For full replacements and new builds, we coordinate the masonry, the ironwork, and the motor as one project with one written scope. Gate Installation in Boston explains the process from measure to final coat.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Motor & Opener in Boston
Most motor failures we see in Boston are winter failures: a photo-eye caked in road salt, a limit switch pushed past travel by ice, or a gear stripped by a gate that froze into the ground and fought the opener. The housing era matters because half the motors in the South End and Back Bay are mounted on pillars that were never designed for automation, so the motor carries load from a frame that moves with the frost. That’s why our Gate Motor & Opener work starts with a load check on the gate itself before we touch the motor.
Motor Repair
Signs you need it
The gate starts, stops mid-travel, reverses for no reason, or hums without moving.
What it costs in Boston
Motor repair in Boston typically runs $180 to $420 depending on the failure and whether the motor is still serviceable.
How we do it
We test the capacitor and limit switches, check the gearbox for salt corrosion, replace the failed component, and photograph the settings before and after.
Motor Installation
Signs you need it
The motor is burned out, the gearbox is stripped, or the opener is obsolete and parts are no longer available.
What it costs in Boston
Full motor replacement in Boston runs $750 to $1,400 installed, including removal of the old unit and new mounting hardware.
How we do it
We remove the old motor, reinforce the mounting plate, install the new unit, set limits and force to the gate’s actual travel, and hand you the photo log before we leave.
What Gate Motor & Opener Costs in Boston
| Item | Typical range in Boston |
|---|---|
| Motor repair | $180 - $420 |
| Motor installation | $750 - $1,400 |
| Limit switch/photo-eye replacement | $150 - $280 |
Can you fix a gate motor the same day in Boston?
Yes. Most motor repairs we complete in one visit, and we carry common parts for LiftMaster, FAAC, and BFT on the truck. Call (928) 260-0864 and we’ll tell you when a technician can be there.
Will my Boston gate motor survive the winter?
A properly set motor on a plumb gate will run through Boston winters without issue. The failures we see are usually from gates that bind against ice or salt-corroded connections, which is why we photograph every setting before leaving.
Gate Access Control in Boston
Access control in Boston is common where driveways are tight and parking is scarce: South End alleys, Charlestown courts, and any building where an unlocked gate means a stranger’s car in your space. Salt air and freeze-thaw cycles do the same damage to keypads, card readers, and phone-entry boxes that they do to the gates themselves. Our Gate Access Control work is built for that, with sealed enclosures and connections rated for the harbor’s humidity.
Keypad Entry
Signs you need it
Codes stop working, the keypad face is cracked or fogged, or the buttons only respond when pressed hard.
What it costs in Boston
Keypad replacement in Boston runs $250 to $500 installed, including programming and a weather-sealed enclosure.
How we do it
We remove the old keypad, install the new unit, seal the wiring against moisture, program the codes, and photograph the final configuration.
Phone Entry
Signs you need it
Visitors can’t reach you from the call box, the line crackles, or the unit won’t dial out at all.
What it costs in Boston
Phone entry repair or replacement in Boston typically lands between $350 and $700, including the new unit and configuration.
How we do it
We test the phone line at the gate, replace the call box if needed, configure the dial-out, and log the settings in the job record.
What Gate Access Control Costs in Boston
| Item | Typical range in Boston |
|---|---|
| Keypad entry | $250 - $500 |
| Phone entry | $350 - $700 |
| Remote control programming | $75 - $180 |
Does a Boston access control system work with my existing motor?
In most cases, yes. We service nine major brands, so we can add keypads, phone entry, or a card reader to the motor already on the property without forcing a replacement. Call (928) 260-0864 for a straight answer.
Can you add a video intercom to a Boston gate?
Yes. We install video intercoms that tie into the gate’s control board, and we document the wiring on every visit so any future technician can read the setup. Boston’s salt air means we use sealed enclosures and marine-rated connectors.
Gate Parts & Welding in Boston
Welding is the core trade in Boston because so many gates here are original iron that can’t be reproduced by swapping panels. The city’s frost heave and road salt mean even a well-built gate needs hinge work, post work, or rail repair eventually. Our Gate Parts & Welding work is done on site with mobile equipment, which matters when the gate is set in a Beacon Hill brick pier that can’t be carried to a shop.
Hinge Replacement
Signs you need it
The gate sags, drags on the ground, or the hinge pin is visibly worn to half its original diameter.
What it costs in Boston
Hinge replacement in Boston runs $120 to $280 per hinge, including cutting out the old weld and welding in the new hinge.
How we do it
We cut the old hinge free, grind the post clean, weld the new hinge in place, and photograph the finished weld for the job record.
Post Replacement
Signs you need it
The post is rusted through at the base, leaned more than a few degrees, or cracked from ice expansion.
What it costs in Boston
Post replacement in Boston runs $300 to $650 per post, depending on whether the base is set in concrete or original granite.
How we do it
We remove the old post, set the new one in concrete at the correct depth, brace it plumb while it cures, and photograph the final position.
What Gate Parts & Welding Costs in Boston
| Item | Typical range in Boston |
|---|---|
| Hinge replacement | $120 - $280 per hinge |
| Post replacement | $300 - $650 per post |
| Custom welding | $150 - $350 per section |
Can you weld a Boston gate without removing it?
Yes. We run mobile welding equipment and do most hinge, rail, and post work on site. The gate stays on the property, and the work is documented with photos before we leave. Call (928) 260-0864 for a written price.
Do you match period ironwork in Boston’s historic districts?
We can match the profile and finish of original ironwork closely, and we’ve worked on gates in Beacon Hill and the South End where the Landmark Commission required it. Bring us a photo and we’ll tell you what’s possible.
Brands We Service in Boston
We carry parts for Viking, Ghost Controls, DoorKing, and Elite, and we service those plus LiftMaster, FAAC, BFT, Linear, and Mighty Mule. Stocked parts in our Boston office mean most common motor repairs go in the first visit. See our brands for the full list.
Pricing for Gate Repair in Boston, MA
| Service | Typical range in Boston |
|---|---|
| Motor repair | $180 - $420 |
| Motor installation | $750 - $1,400 |
| Limit switch/photo-eye replacement | $150 - $280 |
| Keypad entry | $250 - $500 |
| Phone entry | $350 - $700 |
| Remote control programming | $75 - $180 |
| Hinge replacement | $120 - $280 per hinge |
| Post replacement | $300 - $650 per post |
| Custom welding | $150 - $350 per section |
Prices in Boston run higher when the gate is set into original granite or brick that requires a mason’s involvement before we can work, and when the Landmark Commission has to review a proposed repair. What never changes is the Haven Standard: the written price is handed to you before any work starts, and it’s the price you pay. No surprise invoice at the end.
Neighborhoods We Serve in Boston
We repair gates across Boston, from the brick sidewalks of Beacon Hill to the triple-deckers of Dorchester. A typical response time in the metro area is same day or next morning, depending on the time you call and where the technician is coming from.
- Beacon Hill
- Back Bay
- South End
- Charlestown
- Dorchester
Service Area - Cities Near Boston
We work in Somerville, MA, Cambridge, MA, Chelsea, MA, and Everett, MA as well as Boston itself. If you’re on the edge of any of these and aren’t sure, call us and we’ll tell you straight.
Serving Boston, MA - Our Local Coverage Area
We’re based in the Boston area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Boston
Most Boston repair calls get a same-day or next-morning visit. We schedule by urgency and location, not by a call queue. A live person answers the phone 24/7 at (928) 260-0864, and they’ll tell you when a technician can be there.
For repairs in kind, usually not. But if your gate is in a Landmark or Architectural Commission district, like Beacon Hill or the South End, any significant alteration may require review. We can tell you what the existing work looks like against the rules, and we’ll document everything for the record.
You get a written record of the price you agreed to, a photo log of what was found and what was installed, and the part numbers of anything we replaced. That’s Haven Standard Clause 4, and it means no future technician has to guess what was done. Call (928) 260-0864 for your free estimate. And if you want to read more about how we approach gate work broadly, start at our home page.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Boston Customers Say
"Gate had been dragging for a year. They photographed the bent hinge post, explained why the operator kept faulting, and gave me a fixed price to correct both."
- Terrence B."They installed the opener and left me a diagram of the wiring and the limit settings. When I needed a second remote programmed I could do it myself."
- Nadine C."The safety loop had never been installed correctly by the previous company. They showed me the reading, fixed it, and did not charge me for the diagnosis."
- Patrick H.