Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Bedford, TX
Gate Motor & Opener work in Bedford starts with a written price before any tool comes off the truck. Most Bedford repair calls come from gates installed with the original housing stock between 1965 and 1985, now fighting both age and the Blackland Prairie clay that heaves posts out of plumb every wet-dry cycle. Call (928) 260-0864 and you’ll get a live person, a straight diagnosis, and a flat number on paper before work begins.
Why Bedford Homes Are Different
Bedford is a fully built-out Mid-Cities suburb where the bulk of residential lots were developed from the late 1960s through the mid-1980s. That means a large share of the original wooden privacy-fence gates and early ornamental-iron driveway gates are reaching end-of-life at the same time, and the failure pattern is remarkably consistent across neighborhoods like Shady Brook, Stonegate, and the streets east of Central Drive.
The deeper driver of repair calls here is the expansive clay beneath the city. Tarrant County’s heavy Blackland Prairie soil swells when wet and shrinks when dry, and a single drought-to-rain cycle can move a gate post several inches out of plumb. Technicians working in Bedford spend more time shimming hinges and planing latch sides than they do replacing hardware, because posts set correctly in the 1970s have typically drifted enough by now that the gate-to-post gap is no longer uniform. Newer-built suburbs like Keller or Mansfield sit on different conditions and simply don’t generate that same repair pattern. Add in North Texas summers that regularly push above 100°F and oxidize iron gate paint, and you have a repair profile that is distinctly Bedford.
Our Main Bedford Services
Most Bedford homeowners start with one of two calls: a gate that will not close or a property that needs a new gate entirely. Here is what each involves locally.
Gate Repair in Bedford
A sagging gate in Bedford is usually a hinge or post problem before it is a hardware problem. We check the plumb of the post, the gap at the latch side, and the wear on the hinge barrels, then write up exactly what needs to happen with an exact price. Whether it is a warped wooden gate or an ornamental iron frame that has pulled at the weld points, Gate Repair in Bedford starts with evidence and ends with a photo record of everything we touched.
Gate Installation in Bedford
New gate installation on a Bedford lot means accounting for clay soil movement before the first post hole is dug. We set posts below the active soil zone, verify plumb at every stage, and document the entire installation with photos and final measurements. If you are replacing an end-of-life 1970s wooden gate with something built for the next 30 years, Gate Installation in Bedford covers the full scope, from post set to final latch adjustment.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Motor & Opener in Bedford
Gate Motor & Opener repair in Bedford most often involves operators bolted to gate frames that have shifted on clay soil, which means the motor may be fighting a gate that no longer swings true. We service nine major automation brands including Viking, Ghost Controls, and DoorKing, and we will not steer you toward a replacement motor when a limit-switch adjustment or a new capacitor solves it. The Gate Motor & Opener service hub covers the full range of what we do, from arm operators to slide motors.
Motor Repair
Signs you need it
The gate starts, stops short, or reverses mid-travel, or you hear the motor hum but the gate does not move.
What it costs in Bedford
Motor repair in Bedford typically runs $180 to $340, depending on the fault and whether replacement parts are on the truck.
How we do it
We test the capacitor, inspect the limit switches, verify voltage at the board, photograph every reading, and hand you a written price before we turn a single screw.
Motor Installation
Signs you need it
The existing motor has seized, burnt out, or been deemed uneconomical to repair, and you need a new operator mounted and tuned.
What it costs in Bedford
Swing-gate motor replacement in Bedford generally runs $850 to $1,850, while slide-gate operators range from $1,200 to $2,600, depending on brand and gate weight.
How we do it
We pull the old operator, mount and wire the new one, set the travel limits, align the safety photo-eyes, test full open-close cycles, and leave a photo log of every setting.
Linear Motor
Signs you need it
The gate travels unevenly, the linear arm slips, or the motor has been damaged by force or weather exposure.
What it costs in Bedford
Linear motor replacement in Bedford typically runs $1,200 to $2,600, depending on gate length and whether the arm bracket is intact.
How we do it
We remove the failed linear arm, install the new motor and arm, adjust the stroke, verify the force settings, and record every reading before we leave.
Slide Motor
Signs you need it
The slide gate stops at the wrong point, grinds on the rail, or the motor trips its breaker repeatedly.
What it costs in Bedford
Slide motor replacement in Bedford typically runs $1,200 to $2,600, depending on gate weight and whether the rack is still serviceable.
How we do it
We replace the operator, align the rack and pinion, set limits, test obstruction reversal, and photograph the final settings for your record.
What Gate Motor & Opener Costs in Bedford
| Item | Typical range in Bedford |
|---|---|
| Motor repair | $180 - $340 |
| Swing-gate motor replacement | $850 - $1,850 |
| Slide or linear motor replacement | $1,200 - $2,600 |
Can you fix a gate motor the same day in Bedford?
Most motor repairs are same-day when the part is on the truck, which covers the majority of faults in Bedford’s housing stock. Larger operator replacements are typically scheduled within a few days. Call (928) 260-0864 for an exact written quote, free of charge.
Do you work on existing motors, or do you only install new ones?
We repair whatever motor is already on the property. That includes LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. A documented repair usually costs less than a replacement.
Gate Access Control in Bedford
Gate Access Control in Bedford means retrofitting entry systems onto gates that were never wired for them, which is common in this city’s 1965-to-1985 housing stock. We handle keypads, remotes, phone entry, card readers, and video intercoms, and every install includes the wire diagram and photo record that commercial sites have required for years. The Gate Access Control hub covers the full service line.
Keypad Entry
Signs you need it
The existing keypad is unresponsive, cracked from sun exposure, or you want to add coded entry to a gate that currently relies on a remote.
What it costs in Bedford
Keypad installation or replacement in Bedford typically runs $250 to $650, including the controller and programming.
How we do it
We mount the new keypad, run weather-sealed wiring, program the codes, test the release function, and leave a written record of the code structure.
Remote Control
Signs you need it
The remote only works inches from the receiver, the gate ignores the signal, or you need additional remotes programmed.
What it costs in Bedford
Remote programming or replacement in Bedford typically runs $75 to $250, depending on receiver type and remote count.
How we do it
We identify the receiver frequency, program the new remote, test range from the street, and document the process with photos.
Phone Entry
Signs you need it
Visitors need a way to call from the gate without a keypad code, or the existing phone-entry unit has failed after storms.
What it costs in Bedford
Phone entry system installation in Bedford typically runs $500 to $1,500, depending on wiring distance and panel type.
How we do it
We install the call box at the gate, run the line to the house, program the relay, and test the call-to-open function before we leave.
Video Intercom
Signs you need it
You want to see who is at the gate before opening it, or an existing video entry station has a dead screen or no signal.
What it costs in Bedford
Video intercom installation in Bedford typically runs $800 to $2,000, depending on wiring and monitor placement.
How we do it
We mount the camera at the gate, pull the video cable, configure the monitor, and photograph the final setup for your file.
What Gate Access Control Costs in Bedford
| Item | Typical range in Bedford |
|---|---|
| Keypad entry | $250 - $650 |
| Remote control programming or replacement | $75 - $250 |
| Phone entry system | $500 - $1,500 |
Can you add a keypad to an existing gate motor in Bedford?
Yes, in most cases the existing operator has an accessory terminal for a keypad or card reader. We wire the new device, program it, and photograph the finished connection. Call (928) 260-0864 for a written quote.
Do you run the power and wiring for access control?
We handle the low-voltage wiring, the power run from the nearest source, and the programming. The written quote covers all of it before work begins.
Gate Parts & Welding in Bedford
Gate Parts & Welding in Bedford is often the difference between replacing a 40-year-old iron gate and keeping it. Clay soil movement here breaks post footings, shears hinge welds, and twists frames, and a competent weld repair with a properly reset post restores the gate without the cost of a full replacement. The Gate Parts & Welding hub details the full scope of structural work we do.
Hinge Replacement
Signs you need it
The gate sags, scrapes the ground at the latch side, or the hinge barrels show visible wear or cracking.
What it costs in Bedford
Hinge replacement in Bedford typically runs $150 to $400 per hinge set, depending on gate weight and whether the post must be shimmed.
How we do it
We lift the gate, remove the old hinges, weld or bolt the new set, shim the post to close the gap, and photograph the final alignment.
Post Replacement
Signs you need it
The post leans visibly, the gate-to-post gap is uneven top to bottom, or the post has rusted through at ground level.
What it costs in Bedford
Post replacement in Bedford typically runs $400 to $1,200 per post, including concrete and resetting the gate to plumb.
How we do it
We remove the old post, dig below the active clay zone, set the new post in concrete, verify plumb on two axes, and re-hang the gate.
Custom Welding
Signs you need it
The gate frame has a cracked weld, a broken picket, or you need a structural reinforcement added to an aging iron gate.
What it costs in Bedford
Custom welding in Bedford typically runs $100 to $300 per hour plus materials, with most residential repairs falling between $150 and $600.
How we do it
We grind the crack, weld the joint, dress the bead, prime the repair, and photograph before and after for your record.
Gate Rollers
Signs you need it
A slide gate jumps the rail, rolls rough, or the wheels have flat spots from heat and weight.
What it costs in Bedford
Roller replacement in Bedford typically runs $150 to $350 per roller, including alignment to the rail.
How we do it
We swap the worn rollers, align the gate on the rail, test full travel, and leave a photo log of the new hardware.
What Gate Parts & Welding Costs in Bedford
| Item | Typical range in Bedford |
|---|---|
| Hinge replacement | $150 - $400 per set |
| Post replacement | $400 - $1,200 per post |
| Custom welding | $100 - $300 per hour |
Can you weld a cracked iron gate in place, or does it need to come off?
Most cracks can be welded with the gate in place if the hinges are sound and the post is stable. If the post has moved, we reset it first. Call (928) 260-0864 for a written quote.
Do you replace wooden gate posts in Bedford?
Yes, we set treated posts below the clay’s active movement zone, concrete them in, and re-hang the gate plumb. The written price covers digging, concrete, and the final gate adjustment.
Brands We Service in Bedford
We service nine gate-automation brands in Bedford, so the motor already on your gate is the one we repair first. Ghost Controls, DoorKing, Elite, and Viking are common in this housing stock, and we carry parts locally for most of them. Visit our brands page for the full list and typical turnaround on parts.
Pricing for Gate Repair in Bedford, TX
| Service | Typical range in Bedford |
|---|---|
| Motor repair | $180 - $340 |
| Swing-gate motor replacement | $850 - $1,850 |
| Slide or linear motor replacement | $1,200 - $2,600 |
| Keypad entry | $250 - $650 |
| Remote programming or replacement | $75 - $250 |
| Phone entry system | $500 - $1,500 |
| Video intercom | $800 - $2,000 |
| Hinge replacement | $150 - $400 per set |
| Post replacement | $400 - $1,200 per post |
| Custom welding | $100 - $300 per hour |
What pushes a Bedford price toward the top of these ranges is usually soil movement: a post that has drifted far enough out of plumb means more shimming, more welding, and occasionally a full reset before the gate can be re-hung. Every quote is written and handed over before any work starts, so the number on the page is the number you pay.
Neighborhoods We Serve in Bedford
We run calls across Bedford daily, from the older ranch tracts near Shady Brook and Stonegate to the neighborhoods along Central Drive and Harwood Road. Response time from our Dallas-Fort Worth dispatch office to most Bedford addresses is under an hour during normal hours, and emergency calls get the same live-answer line at any hour.
- Shady Brook
- Stonegate
- Woodland Hills
- Bedford Meadows
- Harwood Terrace
Service Area - Cities Near Bedford
Vance Gate Repair serves Bedford and the surrounding Mid-Cities suburbs from our Dallas-Fort Worth dispatch office. That includes Colleyville, TX, Euless, TX, Hurst, TX, and North Richland Hills, TX. Same written-price standard on every job, no matter which side of the city line the gate is on.
Serving Bedford, TX - Our Local Coverage Area
We’re based in the Bedford area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Bedford
Most Bedford calls are reached in under an hour from our Dallas-Fort Worth dispatch office during normal hours. Emergency calls get the same live person at (928) 260-0864 at any hour, and we quote the written price before work starts, not after.
Most gate repairs and like-for-like replacements in Bedford do not require a permit, though new gate installations with new footings may need approval depending on the scope. We flag any permit question in the written quote so there are no surprises.
Yes, every repair and installation we do in Bedford carries the full 365-Day Done Right Promise. If the repair is not right, we make it right at no additional charge. Call (928) 260-0864 for an exact written quote on any gate problem.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Bedford Customers Say
"Good work on a long driveway gate. Arrived when they said, finished when they said."
- Sofia E."Honest about what did not need doing. Told me the operator had years left and only the control board needed replacing."
- Douglas N."Quoted in writing, installed on the day promised, and the price did not move. The crew was licensed and the number was on the paperwork."
- Wes A.