Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Moore, OK
Gate motor and opener work in Moore comes down to two things: the 2013 tornado rebuild wave that put thousands of gates in on fast timelines, and the red clay underneath them that hasn’t stopped moving since. A gate that won’t open here is rarely just a dead motor. It’s usually a motor fighting a post that’s drifted out of plumb, a hinge that’s bound up, or a control board that’s been baked through one too many Oklahoma summers. We diagnose the whole assembly, not just the part that failed. Call (928) 260-0864 and we’ll put a written price in your hand before anything gets touched.
Why Moore Homes Are Different
Moore’s housing stock splits into two rough eras: 1970s through 1990s ranch-style subdivisions, and the post-2013 rebuild neighborhoods that went up after the EF5 tornado. The rebuild-era gates are the ones we’re getting called about now, roughly a decade on. Many were installed by volume contractors working under insurance deadlines, which means fast-set concrete at shallow depths and posts that were never quite right to begin with. Now the shrink-swell clay is finishing the job, torquing posts a few degrees every year until hinges bind and motor arms fight the geometry.
The climate works against gate hardware in specific ways. Southwest winds sandblast finishes. Summer heat warps wood frames and cooks capacitor-based electronics inside control boxes. Ice storms snap hinges and freeze latches shut. But the real recurring problem is the soil. Moore’s expansive clay swells with winter moisture and contracts in summer drought, and that seasonal cycle is why a gate that closed cleanly in March might bind in August. We set posts deeper than code minimums here and photograph everything before we leave.
Our Main Moore Services
Most Moore homeowners reach us for two reasons: a gate that’s failing structurally or mechanically, or a gate that needs to be replaced entirely. Both start with a written diagnosis and a fixed price.
Gate Repair in Moore
A leaning post, a snapped hinge, a gate that drags on the concrete and won’t latch: these are the repair calls we run every week in Moore, from the older subdivisions west of I-35 to the rebuild corridor south of 19th Street. We work on swing and slide gates, wood and steel, and we always check the post footings first, not the hardware. If the post has moved, bolting on a new hinge just buys you six months. Gate Repair in Moore covers the full scope of what we fix, from gate frames to latches to structural realignment.
Gate Installation in Moore
New gate installations in Moore need to account for clay soil movement from day one. That means post holes bored below the frost line, concrete with proper drainage, and gate frames that won’t warp in July. We install wood, steel, and composite gates with automation-ready framing, so if you want a motor later you won’t need to redo the post work. Gate Installation in Moore walks through material options, timelines, and what a complete install includes.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Motor & Opener in Moore
Gate motor and opener service in Moore handles every brand already on the property, from Gate Motor & Opener systems installed during the rebuild to newer smart-enabled units. A Moore gate motor has to push against a gate that clay soil has shifted out of square. That’s why so many motors here burn out arms and boards before the motor itself fails: the electronics are working against a bad geometry they were never designed to fight. We diagnose the entire system, not just the motor, and we service BFT, Linear, Viking, Ghost Controls, and five other major automation brands without steering you toward replacement.
Motor Installation
Signs you need it
Your old motor trips the breaker repeatedly, whines without moving the gate, or is more than 12 years old and starting to fail every few months.
What it costs in Moore
Gate motor replacement in Moore runs $730-$1,880 depending on the brand, the gate’s weight, and whether the arm bracket is still aligned.
How we do it
We pull the old motor, inspect the post alignment, install the new motor with fresh mounting hardware, set the limit switches, and photograph every connection before securing the housing.
Motor Repair
Signs you need it
The gate moves slower than it used to, stops halfway, reverses for no reason, or the motor runs but the gate doesn’t move.
What it costs in Moore
Motor repair in Moore typically runs $130-$380; if the circuit board is shot, expect $230-$440 for the board and labor combined.
How we do it
We test the capacitor, limit switches, and control board, replace only the failed component, and run the gate through five full cycles before we call it done.
Linear Motor
Signs you need it
Your linear arm grinds, stalls under load, or the thread on the drive screw is visibly worn or stripped.
What it costs in Moore
Linear arm motor replacement in Moore runs $650-$1,450 installed, depending on the arm length and whether the bracket needs reinforcement.
How we do it
We match the arm’s throw length to the gate leaf, check the post and gate alignment before install, and set the open and close limits precisely.
Slide Motor
Signs you need it
Your slide gate shudders along the track, the drive chain sags, or the motor runs but the gate doesn’t engage the drive sprocket.
What it costs in Moore
Slide gate motor service in Moore runs $580-$1,440, with full motor replacement at the upper end of that range.
How we do it
We check the track and rollers first, adjust the chain tension, and only then address the motor and its drive sprocket.
Intercom Integration
Signs you need it
Your gate opener works fine but there’s no way for visitors to call the house, or the existing intercom wiring is corroded and crackling.
What it costs in Moore
Adding intercom control to a gate opener in Moore runs $400-$1,100, depending on whether we’re running new wire or using a wireless bridge.
How we do it
We tie the intercom relay into the opener board, test the call path from the post station to the house unit, and document the wiring in the job record.
What Gate Motor & Opener Costs in Moore
| Item | Typical range in Moore |
|---|---|
| Motor replacement | $730-$1,880 |
| Motor repair | $130-$380 |
| Circuit board replacement | $230-$440 |
How long do gate motors last in Moore?
A well-installed gate motor in Moore lasts 8 to 12 years, but soil movement and summer heat shorten that window. Post drift makes the motor fight extra resistance, which burns out boards and gears faster. We can extend motor life by correcting the gate geometry at the same visit. Call (928) 260-0864 for a written assessment.
Can you fix a gate opener that only works sometimes?
Yes. Intermittent operation usually points to a failing capacitor, a cold solder joint on the board, or a limit switch drifting out of position. We test each component under load rather than guessing, and the written price covers what we actually find. Call (928) 260-0864 to schedule a diagnosis.
Gate Access Control in Moore
Gate access control in Moore means more than doorbells and keypads. This is the equipment that decides who gets through without leaving the house, and in a city where a lot of gate hardware was installed quickly, the wiring and weatherproofing often predate the current hardware. Intercom wiring gets brittle in Oklahoma heat, keypad membranes crack, and phone-entry relays get zapped in storms. Our Gate Access Control service covers everything from a single keypad to a full multi-point entry system, with every wire documented and photographed so the next service call doesn’t start from zero.
Keypad Entry
Signs you need it
Your keypad works sporadically, the buttons stick, or you’re giving out the same code to too many people and need to manage access.
What it costs in Moore
Keypad installation or replacement in Moore runs $180-$500, including weatherproof housing and programming.
How we do it
We mount the keypad in a weatherproof box, run or reuse the low-voltage line, and program the master code and up to four entry codes on site.
Remote Control
Signs you need it
You want gate opening from the car without rolling down the window, or the existing remote only works from a few feet away.
What it costs in Moore
Adding or upgrading a remote control receiver in Moore runs $150-$350 including two transmitters.
How we do it
We install the receiver at the opener board, pair the transmitters, and test the range from the street before we hand them over.
Card Reader
Signs you need it
You need to track who enters and when, or you manage a small property in Moore with multiple users and don’t want to change codes constantly.
What it costs in Moore
Card reader installation starts at $500-$900 in Moore for a single pedestal reader with controller and 20 cards.
How we do it
We set the pedestal, run conduit, mount the reader, and program the controller with individual card numbers and access schedules.
Video Intercom
Signs you need it
You want to see and talk to whoever is at the gate before opening it, from your phone or a wall-mounted monitor inside.
What it costs in Moore
Video intercom systems in Moore run $700-$2,800 installed, depending on whether you want a dedicated monitor, a phone app, or both.
How we do it
We install the camera station at the gate, run the communication line, and configure the indoor handset or app so you can unlock from anywhere.
What Gate Access Control Costs in Moore
| Item | Typical range in Moore |
|---|---|
| Keypad entry | $180-$500 |
| Remote control setup | $150-$350 |
| Video intercom | $700-$2,800 |
Does Moore require a permit for gate access control wiring?
Low-voltage wiring for gate access control typically doesn’t require a permit in Moore, but burying conduit or adding an electrical outlet might. We handle the code check for the scope of your job and include any permit coordination in the written price. Call (928) 260-0864 for specifics on your property.
Can I control my gate from my phone if my house already has Wi-Fi?
Yes. Most modern gate control boards support a Wi-Fi bridge or cellular module that ties into the opener. We can add phone control to an existing system for $250-$550, and we document the bridge settings in your job file so it’s easy to re-pair later. Call (928) 260-0864 for a written quote.
Gate Parts & Welding in Moore
Gate parts and welding in Moore is the quiet half of the job no one thinks about until a post is leaning at a fifteen-degree angle. The clay soil here doesn’t just settle: it moves, and it moves differently on the north and south side of the same post. We carry the hardware that fails most often in Moore: heavy-gauge hinges, latch posts, drop rods, and track components. Our Gate Parts & Welding service covers on-site welding, post resetting, and custom fabrication, with the same written price and photo record on every visit.
Hinge Replacement
Signs you need it
Your gate droops, drags on the ground, or the hinge pin is so worn the gate has vertical play you can feel when it moves.
What it costs in Moore
Hinge replacement in Moore runs $160-$380 per gate leaf, including heavy-duty hardware and realignment.
How we do it
We cut off the old hinges, grind the weld points clean, install heavier-gauge hinges, and set the gate back to plumb.
Post Replacement
Signs you need it
Your gate post is leaning more than five degrees, cracked at the base, or concrete is crumbling around it.
What it costs in Moore
Gate post resetting or replacement in Moore runs $350-$700, plus $250-$500 for a new post if the original is split or rusted through.
How we do it
We saw the old post at ground level, dig out the footing, bore deeper than the original, set the new post in concrete with drainage, and brace it while it cures.
Rail Repair
Signs you need it
Your gate rail is bent, rusted through, or broken at a weld point, and the gate catches or shudders as it travels.
What it costs in Moore
Rail repair or replacement in Moore runs $180-$480, depending on the rail length and whether it’s bolted or welded to the posts.
How we do it
We cut out the damaged section, weld in a matched replacement, grind the seam smooth, and check the gate’s travel clearance.
Custom Welding
Signs you need it
You need a bracket, reinforcement plate, or custom gate section that off-the-shelf hardware won’t solve.
What it costs in Moore
Custom gate welding in Moore starts at $150 and typically runs $200-$900 depending on material, complexity, and whether it’s painted after.
How we do it
We measure on site, cut and weld the piece in the shop or in place, and photograph the finished work from three angles.
Gate Rollers
Signs you need it
Your slide gate grinds, jumps the track, or the rollers are flat-spotted and visibly worn.
What it costs in Moore
Gate roller replacement in Moore runs $130-$350 per set, including track adjustment.
How we do it
We swap out the worn rollers, clean the track, and adjust the height so the gate rides without dragging or bouncing.
What Gate Parts & Welding Costs in Moore
| Item | Typical range in Moore |
|---|---|
| Hinge replacement | $160-$380 |
| Post reset or replacement | $350-$700 |
| Custom welding | $200-$900 |
Can you fix a gate that’s leaning but still opens?
Yes, and catching it now saves money. A leaning post in Moore’s clay soil will keep moving until the hinges bind and the motor fails. We reset the post and re-hang the gate in a single visit. Call (928) 260-0864 for a written estimate.
Do you weld on site or take the gate to a shop?
Most welding happens on site. We have a mobile rig for rail repairs, bracket work, and small fabrications. Anything requiring a controlled environment, like a full gate rebuild, goes to our shop and comes back photo-documented at every step. Call (928) 260-0864 to schedule an assessment.
Brands We Service in Moore
We service BFT, Linear, Viking, and Ghost Controls openers in Moore, along with five other major automation brands. Common boards, capacitors, and receiver modules for these units are kept on our service vehicles, so a diagnosis and fix often happen in the same visit. Our brands page lists everything we work on, and we never steer a repair toward a replacement to make our lives easier.
Pricing for Gate Repair in Moore, OK
| Service | Typical range in Moore |
|---|---|
| Motor replacement | $730-$1,880 |
| Motor repair | $130-$380 |
| Circuit board replacement | $230-$440 |
| Linear motor replacement | $650-$1,450 |
| Slide motor service | $580-$1,440 |
| Keypad entry | $180-$500 |
| Remote control setup | $150-$350 |
| Video intercom | $700-$2,800 |
| Hinge replacement | $160-$380 |
| Post reset or replacement | $350-$700 |
| Custom welding | $200-$900 |
| Gate roller replacement | $130-$350 |
What pushes a Moore gate repair to the high end is usually soil movement. A post that has drifted six degrees means the gate has to be re-hung before the motor work makes sense, and that adds a structural step to the bill. What you’ll never see is a surprise line item after the fact: the written price you approve before work starts is the price you pay, and that’s our standard on every job in Moore.
Neighborhoods We Serve in Moore
We take gate repair calls across Moore, from the established neighborhoods west of I-35 to the rebuild communities south and east that went up after 2013. Our service vehicles carry the common parts for every brand we work on, so a Moore call is often a one-visit fix.
- Old Towne Moore
- Greenleaf Trails
- Southmoore
- Kings Manor
- Sycamore Commons
Service Area - Cities Near Moore
From our Oklahoma City dispatch desk, our crews serve Moore and the surrounding metro daily. You’ll find the same written-price standard across Oklahoma City, OK, Norman, OK, Edmond, OK, and Midwest City, OK. Each city gets a dedicated gate specialist who knows the local soil and housing stock, not a rotating crew.
Serving Moore, OK - Our Local Coverage Area
We’re based in the Moore area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Moore
We dispatch to Moore same-day in most cases, and a live person answers the phone 24 hours a day. If your gate is stuck open, stuck shut, or blocking a vehicle, call (928) 260-0864 and we’ll get a technician routed to you with a written price before any work starts.
Many Moore subdivisions have covenants that cover gate appearance and height, especially in the post-2013 rebuild communities. We can help you check what your HOA requires before we order materials. Repair work on an existing gate rarely triggers an approval, but matching the original style keeps it clean.
Most gate repairs and replacements on existing posts don’t require a Moore city permit. New post footings or added electrical work might, especially if you’re adding an opener for the first time. We check the current requirements for your project and include any permit coordination in the written quote. Call (928) 260-0864 and we’ll confirm the scope for your property.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Moore Customers Say
"Gate had been dragging for a year. They photographed the bent hinge post, explained why the operator kept faulting, and gave me a fixed price to correct both."
- Terrence B."They installed the opener and left me a diagram of the wiring and the limit settings. When I needed a second remote programmed I could do it myself."
- Nadine C."The safety loop had never been installed correctly by the previous company. They showed me the reading, fixed it, and did not charge me for the diagnosis."
- Patrick H.