Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Mount Vernon, NY
Gate motor and opener repair in Mount Vernon starts with a written price before any work begins, and most jobs on the city’s older swing-gate stock run between $275 and $1,400 depending on whether the motor, the arm, or the underlying pier needs attention. This page is the Mount Vernon resource for gate motor and opener service, gate access control, and gate parts and welding, written around the specific housing conditions we see here every week – original wrought-iron gates on 80-to-120-year-old brick piers, with freeze-thaw damage showing up as post lean and latch failure every spring. If your gate is dragging or dead, call (928) 260-0864 and a live person answers, any hour.
Why Mount Vernon Homes Are Different
Mount Vernon occupies a specific niche in Westchester County: it has Bronx-level density but early-20th-century suburban housing stock. That combination means gate work here skews heavily toward restoring original ornamental wrought-iron driveway and estate gates on Victorian, Colonial Revival, and inter-war-era two- and three-family homes, most built between 1890 and 1940. The gate posts on these properties are typically set into original brick or brownstone pilasters that have endured a century of ground movement. We regularly arrive to find the gate itself is fine and the problem is the pier: the brick has heaved, the hinge plate has pulled loose, and the gate has dropped half an inch onto the latch or the driveway.
Mount Vernon is an independent municipality, so gate work must comply with the city’s own Building Department permitting requirements rather than county or NYC codes. That’s a local compliance layer many Westchester contractors overlook, and it matters when a post needs re-anchoring or a new gate is going in. Westchester’s freeze-thaw cycle, with ground frost penetrating 24 to 36 inches in hard winters, works against shallow-set brick pilasters every year. On the North Side, large early-1900s homes frequently have original swing gates hung on ornamental iron pintles mortared directly into brick piers – hardware that corrodes badly where the iron contacts the alkaline masonry and hasn’t been serviced in decades. A technician who knows Mount Vernon comes prepared for pintle extraction and re-anchoring, not just hinge lubrication.
Our Main Mount Vernon Services
Most Mount Vernon homeowners call us for one of two reasons: an existing gate that has stopped opening, sagging, or latching correctly, or a new gate that needs to go in on an older property where the piers and layout require real planning. Both are handled start-to-finish from a written scope and price.
Gate Repair in Mount Vernon
Repair work in Mount Vernon usually starts with an original ornamental iron gate that has been on the property since before World War II. The gate itself is often in workable shape; what fails is the hardware around it: pintles seized inside brick piers, hinge plates pulling out of heaved masonry, latch posts that have shifted with the seasons. We remove, re-anchor, realign, and re-hang before touching a motor. Gate Repair in Mount Vernon covers the full scope of what we do for existing gates, including the written estimate and photo documentation on every visit.
Gate Installation in Mount Vernon
New gate installation in Mount Vernon almost always involves an existing set of brick or brownstone pilasters that need to be evaluated before a gate is ordered. We measure pier plumb, check for hidden cracks behind the hinge plates, and confirm the opening width at both the top and bottom before recommending a gate design and operator. The permit process goes through Mount Vernon’s own Building Department. Gate Installation in Mount Vernon walks through what a new gate or full replacement involves here, from first measure to final adjustment.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Motor & Opener in Mount Vernon
Gate motor and opener repair in Mount Vernon typically costs $275 to $1,400, and the most common failure we see is not the motor itself but the geometry around it: a gate that has dropped slightly on a heaved brick pier, which forces the opener arm to work against the misalignment until a gear strips or a limit switch burns out. This is where our Gate Motor & Opener service starts – we find what shifted, correct it, and then address the operator. Because so many Mount Vernon gates are original ornamental iron with substantial weight, the operator has to be matched to the gate’s mass and travel, not just swapped for whatever is on the truck.
Motor Replacement
Signs you need it
The motor hums but the gate doesn’t move, the gate starts and stops mid-travel, or the operator makes a grinding noise and trips its breaker.
What it costs in Mount Vernon
Swing-gate motor replacements in Mount Vernon run $650 to $2,400 for the motor and labor, depending on the brand and whether the arm bracket needs re-anchoring into brick.
How we do it
We disconnect the existing motor, document the wiring and limit-switch positions with photos, reuse the existing arm bracket when the masonry is sound, re-anchor it with lag shields or epoxy anchors when it is not, install the new motor, reset limits, and leave a written record of every setting.
Motor Repair
Signs you need it
The gate drifts after stopping, reverses unexpectedly, or the operator opens but won’t fully close without a second command.
What it costs in Mount Vernon
Motor repair in Mount Vernon runs $275 to $1,400 depending on what failed – a capacitor, control board, gear assembly, or limit-switch mechanism – and whether the arm needs realignment on the pier.
How we do it
We open the operator housing, test the capacitor and board with a multimeter, inspect the gear train and limit cams, replace only the failed part rather than the whole unit, and photograph the repair before closing the cover.
Slide Motor
Signs you need it
The gate jerks along the track, stalls halfway, or scrapes against the rail with enough force to uncover fresh metal.
What it costs in Mount Vernon
Slide motor work in Mount Vernon – typically on commercial or multi-family properties – runs $800 to $4,000 including the chain or rack adjustment and motor replacement when needed.
How we do it
We check the V-track or cantilever rail for level and debris, inspect the chain tension and gear teeth, adjust or replace the motor, and set the open and close limits precisely with the photographed positions recorded in the job file.
What Gate Motor & Opener Costs in Mount Vernon
| Item | Typical range in Mount Vernon |
|---|---|
| Gate motor repair | $275 - $1,400 |
| Slide motor replacement | $800 - $4,000 |
| Swing-gate motor replacement | $650 - $2,400 |
How long does a gate motor replacement take in Mount Vernon?
Most Mount Vernon motor replacements finish in two to four hours on site, assuming the existing arm bracket and masonry are sound. When the brick pier needs re-anchoring first, expect the job to stretch across a second visit to let the epoxy or mortar cure.
Will a new motor fix my sagging gate?
No. A new motor will not fix a gate that has dropped on a shifted brick pier, and forcing it to work that way is how new motors fail within a year. We re-hang or realign the gate before mounting the operator. Call (928) 260-0864 for an exact written quote.
Gate Access Control in Mount Vernon
Gate access control in Mount Vernon is usually added to an existing ornamental driveway gate where the homeowner wants keypad or phone entry without drilling through original ironwork. The challenge here is routing low-voltage wiring cleanly across brick piers and through 100-year-old pilasters without chipping the masonry or leaving a surface-mounted eyesore. Our Gate Access Control service covers keypads, remotes, phone entry, card readers, and video intercoms, all tied into whatever motor is already on the gate.
Keypad Entry
Signs you need it
Family members and regular visitors need a code to open the gate without a remote, or the existing keypad has died from weather exposure.
What it costs in Mount Vernon
Keypad entry in Mount Vernon runs $350 to $1,000 installed, including the watertight housing, wiring run, and programming for multiple unique codes.
How we do it
We mount the keypad on a gooseneck pedestal or flush into the brick pier, run the low-voltage wiring in conduit where it crosses the driveway, and program the codes with a written record of the settings left with you.
Video Intercom
Signs you need it
You want to see and speak with whoever is at the gate before opening it, or a delivery driver needs a way to call the house without a gate code.
What it costs in Mount Vernon
Video intercom systems in Mount Vernon run $1,500 to $3,000 installed, depending on whether it is a single-door station or a multi-tenant setup.
How we do it
We install the camera station at the gate, run the wiring back to an indoor monitor or your phone app, test the two-way audio and video in both daylight and dark conditions, and photograph the final wiring connections for the job file.
What Gate Access Control Costs in Mount Vernon
| Item | Typical range in Mount Vernon |
|---|---|
| Keypad entry | $350 - $1,000 |
| Video intercom | $1,500 - $3,000 |
| Card reader | $400 - $1,200 |
Can you add a keypad to an existing gate motor?
Yes, most motors from Ghost Controls, DoorKing, Elite, and Mighty Mule accept a third-party or matching keypad. We verify compatibility with the specific board in your operator before ordering parts. Call (928) 260-0864 for a written quote.
Does access control work when the power is out?
Most systems have battery backup either built into the operator or added separately, but keypads and card readers themselves draw little power and typically keep working through brief outages. We test the fail-safe behavior on every install so you know exactly what the gate will do if power drops.
Gate Parts & Welding in Mount Vernon
Gate parts and welding in Mount Vernon usually means one thing: the iron has outlasted its hardware. Original ornamental gates on the North Side and Fleetwood often have pintles, hinge straps, and latch bars that are original to the 1920s; the iron is thick and worth keeping, but the moving parts have seized, corroded, or snapped where they meet the alkaline brick. Our Gate Parts & Welding service repairs and fabricates hardware to match the existing ironwork, and we document every weld and replacement part in the job record.
Hinge Replacement
Signs you need it
The gate scrapes the ground on the latch side, the hinge pin has worn into an oval, or the gate lifts noticeably when you swing it by hand.
What it costs in Mount Vernon
Hinge replacement in Mount Vernon runs $250 to $900 per gate, including extracting the old pintles from the brick pier and setting new ones in epoxy or lead.
How we do it
We cut or drive the old pintles out without damaging the brick, re-drill the pier cleanly, set new pintles in structural epoxy, and re-hang the gate to clear the driveway with the weight balanced across both hinges.
Custom Welding
Signs you need it
A picket has cracked at the weld point, the top rail has separated from a stile, or a previous repair was brazed badly and is failing again.
What it costs in Mount Vernon
Custom welding on ornamental iron gates in Mount Vernon runs $150 to $900 per repair, depending on the location, access, and whether we need to forge a replacement picket to match the original profile.
How we do it
We clean the break back to sound metal with a grinder, weld with a process matched to the original iron, grind the bead flush to match the surrounding profile, and prime and paint the repair to blend with the existing patina.
What Gate Parts & Welding Costs in Mount Vernon
| Item | Typical range in Mount Vernon |
|---|---|
| Hinge replacement | $250 - $900 |
| Custom welding | $150 - $900 |
| Gate roller replacement | $150 - $450 |
Can you match the original ironwork on a 100-year-old gate?
Yes. We keep a stock of common ornamental profiles and can forge or grind replacement pickets, finials, and strap hinges to match what is already on the gate. The match is close enough that the repair disappears into the original iron.
How do you fix a gate post that has leaned from frost?
We dig down to the base of the pier, straighten it or re-set the hinge plate with a steel anchor, and backfill with compacted stone to improve drainage. The gate is then re-hung to the corrected alignment. Call (928) 260-0864 for a written scope and price.
Brands We Service in Mount Vernon
We work on whatever motor is already on your Mount Vernon gate. Common brands in the city include Ghost Controls, DoorKing, Elite, and Mighty Mule, and we keep parts for all of them in the truck to avoid a second visit. See our brands for the full list of nine automation lines we service.
Pricing for Gate Repair in Mount Vernon, NY
| Service | Typical range in Mount Vernon |
|---|---|
| Gate motor repair | $275 - $1,400 |
| Swing-gate motor replacement | $650 - $2,400 |
| Slide motor replacement | $800 - $4,000 |
| Keypad entry | $350 - $1,000 |
| Card reader | $400 - $1,200 |
| Video intercom | $1,500 - $3,000 |
| Hinge replacement | $250 - $900 |
| Custom welding | $150 - $900 |
| Gate roller replacement | $150 - $450 |
What pushes a Mount Vernon price toward the top of a range is almost always the masonry: a brick pier that has heaved enough to require re-anchoring with epoxy, or a brownstone pilaster that needs careful drilling rather than bolting. Whatever the number, it is written and handed to you before any work starts – no surprises on the invoice.
Neighborhoods We Serve in Mount Vernon
We work across all of Mount Vernon, from the North Side’s early-1900s estate gates to the tighter two-family lots near the Bronx border. Most repair calls are reached within one to two hours, and emergency gate-down calls are prioritized because a gate stuck open is a security problem, not just an inconvenience.
- North Side
- Fleetwood
- Chester Heights
- Oakwood Heights
- South Side
Service Area - Cities Near Mount Vernon
We also cover the surrounding Westchester communities, including New Rochelle, NY, Yonkers, NY, Harrison, NY, and White Plains, NY. Dispatch is coordinated from our New York City office, and crews serve Mount Vernon locally, so response times are consistent across the service area.
Serving Mount Vernon, NY - Our Local Coverage Area
We’re based in the Mount Vernon area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Mount Vernon
Most emergency calls in Mount Vernon are reached within one to two hours. A gate stuck open is treated as a priority, and a live person answers the phone 24/7 to take the call and dispatch a named technician with a photo sent before arrival.
Repairs that keep the same footprint and do not alter the piers or foundation typically do not need a permit. Replacing a post, rebuilding a pier, or installing a new gate usually goes through Mount Vernon’s Building Department, and we handle that paperwork as part of the job.
Yes. The written price is handed to you before any tool comes off the truck, and it covers the scope, parts, and labor without vague allowances. We also offer a free second opinion on any written estimate from another company. Call (928) 260-0864 to schedule.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Mount Vernon Customers Say
"Gate had been dragging for a year. They photographed the bent hinge post, explained why the operator kept faulting, and gave me a fixed price to correct both."
- Terrence B."They installed the opener and left me a diagram of the wiring and the limit settings. When I needed a second remote programmed I could do it myself."
- Nadine C."The safety loop had never been installed correctly by the previous company. They showed me the reading, fixed it, and did not charge me for the diagnosis."
- Patrick H.