Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Moore
A gate that won’t open, sags into the driveway, or groans every time the motor engages is a different problem in Moore than it is in most places. The red clay under your posts swells and contracts seasonally, and if your gate went in during the post-2013 rebuild, it’s likely been fighting the ground for a decade. We service every swing and slide gate across Moore neighborhoods, from south-of-19th subdivisions along the tornado corridor to older 1970s ranch blocks near I-35. Our Gate Repair crews reset posts, replace worn hinges, retrofit obsolete control boards, and realign gates so they close flush and lock tight. Call (928) 260-0864 and a live person answers, day or night.
Why Vance Gate Repair Is Moore’s Preferred Gate Repair Company
We’re not the newest gate company in Moore, but we’re the one that documents what we find. Every visit ends with a written record: what was out of spec, what we adjusted, what part number went in, and photos of the work. That matters when a gate fails twice and you want to know why.
Our technicians know the Moore housing stock. They recognize a rebuild-era hinge post poured shallow in fast-set concrete the moment they see the lean. They know that a wood gate on the west side of a property off SW 34th will warp faster than the same gate on a shaded north side. And they know that a control board installed before UL 325 took effect won’t have the photo-eye wiring a safe automatic gate needs today.
We answer the phone 24 hours a day. Not a voicemail tree, not a callback queue. When a gate fails and your truck is stuck in the driveway at 6 a.m., someone from our office picks up. Dispatch to Moore is coordinated from our Oklahoma City office, and crews are on the road to Moore the same day for most calls.
Adrian Vance started this company in 2014 out of commercial access-control work, where every repair gets logged and photographed because a facility manager won’t pay twice for the same fault. We brought that same habit to residential gates in Moore. If the repair isn’t right within a year, we make it right at no charge. That’s our Done Right Promise, and it’s written into every job record.
Our Gate Repair Services in Moore
Electric Gate Repair
Electric gate operators in Moore fail most often because the control board is old, or because a limit switch drifted and the gate now over-travels into the post. We service operators from Linear, Viking, BFT, and Ghost Controls, among others, and we stock common control boards, limit switches, and photo-eyes so most electric repairs happen in one visit. If your gate opens but won’t close, or reverses mid-cycle, we trace the loop detector, the photo-eye alignment, and the board before recommending any replacement. Written price first, every time.
Automatic Gate Repair
Automatic gates in Moore carry an extra concern: many pre-2016 installations lack the entrapment protection required by current UL 325 standards. That means no photo-eye at the gate opening and no reversing edge on the leading edge of the gate leaf. We can retrofit those safety devices onto most existing operators without replacing the motor. If the board is too old to accept them, we’ll show you the wiring diagram and explain the retrofit versus replacement cost in writing before we touch a tool.
Hinge & Post Repair
This is the most common gate repair ticket in Moore right now. The 2013 EF5 tornado triggered a reconstruction wave that installed thousands of gates between 2013 and 2016, many by volume contractors working under insurance deadlines. We regularly dig up hinge posts in south Moore neighborhoods near the tornado corridor and find fast-set concrete at 18 inches, when the frost line and the clay movement here really call for 30-plus inches and a wider bell. We excavate the old footing, pour to spec, re-set the post plumb, and re-hang the gate so it swings clean.
Gate Realignment
A gate that drags, bounces off the latch post, or leaves a six-inch gap at the top may not need new hardware at all. Moore’s expansive clay heaves post footings seasonally, and a gate that was perfectly level in 2017 can be out of plumb by 2025. We use a combination of post re-shimming, hinge adjustment, and sometimes weld repairs to bring the gate back to true. On a leaning post that’s structurally sound but shifted, a realignment is usually the cheaper fix, and we’ll tell you honestly when it won’t hold.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterTrusted Brands We Service in Moore
We work on whatever motor is already on your property. That includes Linear and Viking swing operators common in Moore, BFT hydraulic arms on heavier steel gates, and Ghost Controls retrofit kits on wooden driveway gates. We don’t steer you toward a replacement brand because we happen to sell it. We repair the operator you have when it’s repairable, and we stock the wear parts, boards, and remotes that keep Moore gates running without a week-long wait.
If you’re not sure what brand your operator is, open the cover and send us a photo. We’ll identify it and quote the repair before we dispatch.
Common Gate Repair Problems We See in Moore Homes
- Leaning hinge posts on rebuild-era gates. Fast-set concrete at shallow depths cannot resist Moore’s expansive red clay. The post walks out of plumb over a few wet-dry cycles, and the gate starts dragging or binding. We reset the post with a deeper footing, not with a shim job that fails next spring.
- Warped wood gate frames. Moore’s summer heat, especially on unshaded west-facing runs, dries and twists wood gate leaves. A one-inch warp creates enough sag to pop hinge screws out of the post or flex the latch out of alignment. We brace the frame and reset the hinges to compensate.
- Obsolete control boards without entrapment protection. Gates installed before UL 325 updates often have no photo-eye and no reversing edge. The board may still work, but the gate is unsafe by current standards and can close on a child or pet. We retrofit safety devices where the board allows, and quote a board replacement when it doesn’t.
- Ice-storm latch damage. Moore’s winter ice events freeze gate latches shut, and homeowners force them open with a pry bar or a vehicle. The result is a sheared latch bolt, a bent strike plate, and sometimes a cracked weld at the hinge. We replace the latch and repair the weld in one visit, then apply a dry lubricant that doesn’t attract Oklahoma dust.
Pricing for Gate Repair in Moore, OK
We quote flat prices in writing before any work starts. A hinge re-set and post realignment on a typical Moore swing gate runs $220 to $450 depending on how much of the old footing needs excavation. A control board replacement for a common residential operator runs $280 to $520 including the part and calibration. Photo-eye retrofits run $140 to $260 per gate opening, and a full operator replacement on a residential swing gate runs $850 to $1,600 depending on the brand and the condition of the existing bracket and arm. Every quote includes a photographed before-and-after record, part numbers, and a one-year guarantee under our Done Right Promise. If you have a written estimate from another company, bring it in and we’ll review it at no cost.
We Also Serve Cities Near Moore
Our Gate Repair in Moore service area extends to the communities that share Moore’s soil and summer heat. We run service calls to Oklahoma City, Norman, Edmond, and Midwest City, with the same written pricing and same photo-documentation habit on every job. Oklahoma City dispatch coordinates all routes, and Moore crews are on the road daily.
Serving Moore, OK - Our Local Coverage Area
We’re based in the Moore area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Repair in Moore
The gates installed after the 2013 tornado are all hitting their first major wear cycle at the same time, roughly a decade later. Many of those posts were poured shallow in fast-set concrete by volume contractors working under insurance deadlines, and Moore’s expansive red clay has been working against them ever since. The soil swells with winter moisture and contracts in summer drought, and that cycle slowly torques a shallow post out of plumb. Call (928) 260-0864 and we’ll tell you whether your post needs a reset or just a realignment.
In most cases, yes, it can be saved. We dig out the old footing, pour a deeper base with the post re-set plumb, and re-hang the gate with fresh hinge hardware. A full replacement is only needed when the post itself is rotted, cracked, or the gate leaf has structural weld failures. We’ll show you a photo of the old footing before we quote the fix, and the written price covers the whole job.
Many do not. Automatic gate operators installed before 2016 often lack the photo-eye and reverse-edge entrapment protections that UL 325 now requires. If your gate will close on an obstruction without reversing, call us for a safety assessment. We can retrofit photo-eyes and edge sensors onto most existing operators, and we’ll show you the wiring change before we make it.
In Moore, the wood itself is usually the problem. Summer heat dries and warps the gate frame, and no hinge adjustment will hold if the wood is twisting. We brace the frame with a tension rod or a steel angle, then reset the hinges to the corrected geometry. The brace is what stops the sag from returning. Call (928) 260-0864 and describe the gate size and we’ll quote it over the phone.
Often, yes. If the post is still set deep and hasn’t cracked, the shift is usually in the hinge hardware or the post has tilted slightly without losing its footing. A realignment re-achieves plumb and sets the hinges so the gate closes flush. If the post itself is moving seasonally, we’ll catch that on the same visit and recommend a more permanent fix. The realignment is quoted before we start, and the price doesn’t change after we’re done.
Call Vance Gate Repair for Gate Repair in Moore, OK
A leaning post, a dead operator, a latch that won’t engage. Whatever your gate is doing, we’ll name the problem, name the price, and fix it. You get a written scope and a written price before any work starts, a photo record when we leave, and a year of coverage if the repair isn’t right. Call (928) 260-0864 for a free estimate, or send a photo of the gate and we’ll tell you what we’re looking at.
Written by Adrian Vance, Owner at Vance Gate Repair, serving Moore since 2014.
Gate Repair in Nearby Areas