Gate Repair in Irving - Fixed Today, No Surprise Invoice

Gate Repair in Irving, TX

Gate motor and opener repair in Irving is shaped by two things: Las Colinas, whose HOA-managed communities and corporate campuses run commercial-grade operators that fail differently than residential units, and the Blackland Prairie clay that heaves gate posts out of alignment every wet-dry cycle. Most Irving calls we take are for gate operators that stopped mid-travel, keypads that stopped recognizing codes, or weld failures on older ornamental iron. Call (928) 260-0864 and a live person answers, any hour.

Call (928) 260-0864

Why Irving Homes Are Different

Irving’s housing stock splits into two distinct gate-repair markets. Original Irving, built through the 1950s to 1970s, holds hundreds of ornamental wrought-iron driveway gates on single-family lots. Those gates show decades of rust at the hinge welds and post bases. The Las Colinas-era townhome and patio-home communities, built from the late 1970s onward, came with community-entry automatic gates from day one, and many of those original LiftMaster and Linear operators are now at end of life.

The soil is the quiet variable. Irving sits on expansive clay that swells after heavy rain and shrinks in summer drought. That cycle torques gate posts out of plumb, which throws limit switches out of calibration, which is why the same property can call us two or three times in a single year. Summer heat above 100°F also degrades operator circuit boards and photo-eye wiring faster than in milder Texas markets. In Las Colinas especially, we do more commercial-grade swing and slide operator work, access-control panel integration, and HOA compliance documentation than we would in a purely residential suburb.

Our Main Irving Services

The two services Irving homeowners call about most are gate repair and gate installation, and each has its own Irving page with full local detail.

Gate Repair in Irving

When a gate stops closing, drags on the ground, or makes a grinding noise, most Irving homeowners want a diagnosis before a sales pitch. Our repair visits start with a written scope and a written price, handed over before any work begins. We photograph what we find, what we adjust, and what we replace, and we leave that record with you. Gate Repair in Irving covers the full repair picture, including emergency response for gates stuck open or closed.

Gate Installation in Irving

New gate installation in Irving means matching the gate to the neighborhood. A 1960s original-Irving driveway needs a different post-depth and hinge strategy than a Las Colinas patio home with HOA design rules. We measure, spec the gate and operator together, and produce a written price before any order is placed. Gate Installation in Irving walks through the process from measure to final walkthrough.

Before

After

Gate Motor & Opener in Irving

Gate motor and opener service in Irving is our highest-volume work. The 1970s-vintage community-entry operators in Las Colinas are aging out, and the clay-soil post movement across Irving throws limit switches and safety loops out of calibration more often than homeowners expect. When an operator fails here, it is usually the board, the limit switch, or the capacitor, and the fix is almost always faster and cheaper than a full replacement. We service nine automation brands, including LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, so the motor already on your property is the motor we work on. Learn more on our Gate Motor & Opener hub.

Motor Installation

Signs you need it

The operator hums but the gate does not move, or the motor trips its breaker repeatedly.

What it costs in Irving

Most Irving motor installations run between $450 and $1,150 for the unit and labor, depending on brand and whether the arm bracket is intact.

How we do it

We remove the old operator, check the post alignment and bracket condition, mount the new motor, set travel limits, and test the safety reverses before we leave.

Motor Repair

Signs you need it

The gate opens but will not close, closes but will not open, or stops halfway and reverses for no visible reason.

What it costs in Irving

Motor repair in Irving typically runs $180 to $340 when the fix is a capacitor, limit switch, or control board component.

How we do it

We diagnose the failure with a meter, name the failed part, give you the written price, then replace the component and photograph the new setting or part in place.

What Gate Motor & Opener Costs in Irving

Which gate motor brand should I choose for an Irving home?

The brand already on the post is usually the right answer. We service all nine major brands, so we can repair what is there instead of steering you toward a replacement. Call (928) 260-0864 for a written quote on repair or replacement.

Can you service a Viking or Ghost Controls motor in Irving?

Yes. We service Viking and Ghost Controls operators regularly across Irving, including Las Colinas community entries and single-family driveway gates. Parts for both are commonly in local stock.

Gate Access Control in Irving

Gate access control in Irving leans heavier on HOA and multi-tenant systems than in surrounding cities. Las Colinas property managers run card readers, phone-entry systems, and video intercoms at community entries where a single control board failure can lock out dozens of residents in one afternoon. Irving’s summer heat also shortens the life of keypad membranes and card-reader circuitry, so we see more weather-related access-control failures here than in milder Texas markets. We handle the full Gate Access Control stack, including integration with existing gate operators and panel wiring.

Keypad Entry

Signs you need it

The keypad accepts some codes but not others, or the buttons have gone soft and unresponsive after years of Texas sun.

What it costs in Irving

Keypad entry repair or replacement in Irving typically runs $150 to $400 depending on whether we are swapping a membrane or rewiring the unit.

How we do it

We test the keypad output at the control board, isolate the failure to the pad or the wiring, replace what is failed, and reprogram your codes.

Video Intercom

Signs you need it

The video feed is dark, the call button does not ring the house, or the unlock relay fires intermittently.

What it costs in Irving

Video intercom repair and replacement in Irving runs $275 to $700, including camera, indoor monitor, and wiring checks.

How we do it

We check power at the monitor, continuity on the call wires, and the relay at the gate operator, then replace the failed component and photograph the finished wiring.

What Gate Access Control Costs in Irving

Can you integrate access control with an existing LiftMaster gate operator in Irving?

Yes. We regularly wire keypads, card readers, and intercoms into existing LiftMaster operators across Irving, especially in Las Colinas community entries. We match the relay voltage and photograph every connection.

Do HOA gates in Irving need a different access-control setup than single-family gates?

They usually need a panel that supports multiple credentials and logging. We recommend hardware that tracks entry events and integrates with the operator already on site. Call (928) 260-0864 for a written scope.

Gate Parts & Welding in Irving

Gate parts and welding in Irving splits between two jobs: hinge and post repair on the older wrought-iron gates in original Irving, and rail and roller replacement on the slide gates that dominate Las Colinas commercial and mixed-use entries. The clay soil here is the common thread, it heaves posts out of alignment and puts welds under load until they crack at the hinge barrel or the post base. Our Gate Parts & Welding work always includes a written price and a photo record of the weld before and after.

Hinge Replacement

Signs you need it

The gate sags on the latch side, scrapes the ground at the swing arc, or the hinge barrel has visible cracks.

What it costs in Irving

Hinge replacement in Irving typically runs $120 to $300 per hinge, including cutting out the old weld and re-welding the new barrel.

How we do it

We support the gate, cut the failed hinge free, grind the post clean, weld the new hinge in place, and photograph the finished weld.

Rail Repair

Signs you need it

The slide gate jerks or binds mid-travel, or the rail shows a visible dip or bow where the rollers ride.

What it costs in Irving

Rail repair in Irving runs $250 to $550 depending on rail length and whether the existing rail can be straightened or needs a spliced section.

How we do it

We check the rail for level and straightness, cut out the damaged section or re-align the run, weld in the replacement, and reset roller spacing.

What Gate Parts & Welding Costs in Irving

Can you weld a broken ornamental iron gate in Irving without replacing the whole gate?

In most cases, yes. We cut out the failed section, weld in matching stock, and grind the repair so it reads as part of the original design. Call (928) 260-0864 with a photo and we will give you a written price.

Why do Irving gate posts keep going out of alignment?

Irving’s Blackland Prairie clay swells when wet and shrinks when dry, which torques posts out of plumb. We reset posts in concrete with proper depth and drainage so the heave cycle has less effect on the gate.

Brands We Service in Irving

We service Viking, Ghost Controls, DoorKing, and Elite operators in Irving, among the nine brands we stock parts for. Common boards, limit switches, and remotes are kept locally, so most repairs do not wait on a parts shipment. See our brands for the full list.

Pricing for Gate Repair in Irving, TX

Neighborhoods We Serve in Irving

We dispatch gate repair crews to every corner of Irving, from the original 1950s neighborhoods around the Heritage District to the Las Colinas urban center and the townhome communities along MacArthur Boulevard. Response time across Irving is typically same-day for motor and opener failures and next-day for scheduled welding or access-control work.

• Las Colinas
• Heritage District
• Valley Ranch
• North Irving
• MacArthur Boulevard corridor

Service Area - Cities Near Irving

Vance Gate Repair serves Irving and the surrounding Dallas-Fort Worth market. We also dispatch to Dallas, TX, Balch Springs, TX, Mesquite, TX, and Lancaster, TX for gate motor, access-control, and welding work.

FAQs About Gate Repair in Irving