Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Burlington
A new driveway or commercial gate installation in Burlington typically runs $2,800 to $11,500 depending on the gate type, automation, and whether the job requires access control integration with an existing card-reader or keypad system. We install sliding gates, swing gates, pedestrian gates, and security gates throughout Burlington, and we coordinate every step, from the initial site walk to the final safety check. If you’re weighing a repair against a replacement, call (928) 260-0864 and we’ll give you an honest read on what your existing hardware is worth. Our crews know Burlington’s streets, its commercial corridors, and the specific ways New England winters wear down gate hardware year after year.
Why Vance Gate Repair Is Burlington’s Preferred Gate Installation Company
Most gate companies in this area do residential work. Vance Gate Repair built its reputation on commercial access control, and that background makes a real difference on Burlington’s Middlesex Turnpike and Cambridge Street corridors, where Gate Installation usually means more than hanging a gate. It means integrating a new slide gate operator with the facility’s existing DoorKing keypad, coordinating loop detector placement with an in-house IT team, and documenting every adjustment before we leave. Homeowners get the same standard: a written price before work starts, a photo record when the job is done, and a 365-day promise that if something isn’t right, we make it right with no fee.
We’ve seen what Burlington’s winters do to gate hardware. Posts that weren’t set below the frost line heave every spring. Plows catch bottom rollers along commercial driveways and bend them into scrap. Control boards on operators from the 1990s simply can’t accept modern safety photocell retrofits. Knowing what fails and why is half the job, and it’s why Burlington customers call us when they want an installer who can explain the difference between a $400 hinge repair and a $7,000 replacement gate without steering them wrong either way.
Our Gate Installation Services in Burlington
Driveway Gate Installation
Burlington’s residential stock skews heavily toward colonials, garrison colonials, and split-levels built between the 1960s and 1990s. A lot of those homes had decorative aluminum or wrought-iron driveway gates added in the 1980s and 90s, which means the posts, hinges, and latches are now 30 to 40 years old. When we install a new driveway gate in Burlington, we’re usually working around existing concrete, old post footings that may need to be dug out and re-poured, and driveway slopes that complicate swing geometry. We quote the post work, the gate, the operator, and the electrical run as separate line items so you can see exactly where the money goes.
Pedestrian Gate Installation
Pedestrian gates next to driveway gates are common in Burlington, especially on commercial properties where employees walk in while vehicles drive through separately. A new pedestrian gate with a keypad or card reader typically runs $900 to $2,800 installed, depending on the gate material and whether it ties into the same access control system as the main vehicle gate. We set the post below frost depth, align the latch so it doesn’t bind after the first spring thaw, and leave you with a photo log of the finished install.
Sliding Gate Installation
Sliding gates dominate Burlington’s commercial corridors, where space is tight and swing gates would block traffic or snow storage. A cantilever sliding gate with automation on Middlesex Turnpike typically runs $4,500 to $11,500 installed, depending on gate length, operator brand, and access control integration. The installation involves a concrete track, a rack and pinion or chain drive, a loop detector for vehicle detection, and safety photocells. We coordinate the full scope with your security or IT team, because a slide gate on an office park is never a standalone job.
Swing Gate Installation
Residential swing gates are the most common installation we do in Burlington’s neighborhoods, especially on properties along Cambridge Street and the side streets off Route 128. A double swing gate with automation typically runs $3,200 to $8,000 installed, with single swing gates starting around $2,800. The two factors that matter most in Burlington are the post footings and the hinge hardware. We set posts 48 inches deep to get below Middlesex County’s frost line, and we use adjustable hinges that let us compensate for the seasonal movement every New England gate experiences.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterTrusted Brands We Service in Burlington
We work on nine gate-automation brands, but in Burlington we most often field calls about Viking, Ghost Controls, and DoorKing operators, plus Elite for commercial slide gates. If the motor on your gate is still running but the control board is obsolete, we don’t automatically push a full replacement. Sometimes a retrofit kit or a new safety edge is all you need. When a replacement is the right call, we’ll show you the written price for the new unit before we order anything, and we’ll match the operator to whatever access control system your property already uses. Every Burlington job gets a documented photo record of the equipment we installed and the settings we programmed.
Common Gate Installation Problems We See in Burlington Homes
- Legacy operators with dead-end control boards. Many Burlington gates installed in the 1990s are running on control boards that can’t accept modern safety photocell retrofits. When the board goes, the gate gets stuck in manual mode, and the honest answer is often a full operator replacement rather than a board swap we can’t guarantee.
- Sagging aluminum gates from frost heave. Burlington’s frost depth is about 4 feet, and posts set shallower than that shift every spring. The gate hangs lower, the latch misses, and the hinges bind. We reset the posts properly and hang the gate so it stays square through the thaw cycle.
- Plow-damaged slide gates and rollers. Along Middlesex Turnpike and the commercial lots off Cambridge Street, winter plows catch the bottom of slide gates and bend rollers, sweeps, and operator arms. We replace the damaged hardware and set the gate so it clears the plow path without sacrificing the seal at the bottom.
- Automation added to gates that were never designed for it. A decorative 1980s swing gate hung as a manual gate doesn’t always have the structural stiffness for an operator. We check the post depth, the hinge post diameter, and the gate weight before we recommend automation. If the gate can’t handle it, we’ll tell you before you spend the money.
Pricing for Gate Installation in Burlington, MA
Here’s what gate installation in Burlington actually costs, in dollars, based on the work we do here:
| Service | Typical Burlington Range |
|---|---|
| Single swing gate with automation | $2,800 - $5,500 |
| Double swing gate with automation | $3,200 - $8,000 |
| Cantilever sliding gate with automation | $4,500 - $11,500 |
| Pedestrian gate with keypad | $900 - $2,800 |
| Security gate with access control integration | $5,000 - $14,000+ |
| Post replacement (per post, below frost line) | $600 - $1,400 |
What moves the price in Burlington: gate length and material, whether the operator needs to tie into an existing card-reader system, whether we’re running power to a gate that has none, and whether the old posts can be reused or need to be dug out to 48 inches. You get the written quote before we start, and that price is the price. Estimates are free. Call (928) 260-0864 and we’ll walk the site and hand you a number.
We Also Serve Cities Near Burlington
Our crews handle gate installation throughout the Route 128 belt. If you’re in Woburn, Wilmington, Lexington, or Billerica, we’ll send the same team with the same written-price standard. And if you’re specifically looking for Gate Installation in Burlington, we’re already working on your street.
Serving Burlington, MA - Our Local Coverage Area
We’re based in the Burlington area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Burlington
Yes, in most cases we can replace the operator while keeping your existing card-reader or keypad access control intact. The critical step is matching the new operator’s inputs to your access control panel’s relay outputs, and verifying the safety photocell and loop detector wiring carries over cleanly. We do this regularly on Burke County office parks and commercial lots where the IT team needs the access logs to keep functioning without interruption. Call (928) 260-0864 and we’ll confirm the integration path before we order anything.
It depends on the post depth and the gate condition, but we’ll give you a straight answer after a site visit. If the posts were set above Burlington’s 4-foot frost line, they’ll keep shifting and any hinge repair is temporary. If the posts are sound and the gate itself isn’t corroded through, we can sometimes retrofit with adjustable hinges and a new operator for $1,200 to $3,000. If the gate is aluminum, 30-plus years old, and sagging at the midrail, replacement is usually the cheaper long-term answer. We’ll show you photos of what we found and quote both options in writing.
Yes, a solar operator is a solid option for a gate with no nearby power run, and Ghost Controls makes a kit that handles double swing gates. The practical limits in Burlington are winter sunlight and gate weight. Solar operators work best on gates under about 1,200 pounds total, and they need a panel positioned for southern exposure. For a commercial property on Middlesex Turnpike that sees daily vehicle traffic, we’ll also recommend a battery backup so the gate keeps cycling during short winter days. Call (928) 260-0864 for a written quote on the full solar install.
Yes. On a commercial slide gate in Burlington, loop detectors and photocells are not optional add-ons. They’re the UL 325 safety requirement for automated gates, and they’re what keeps a vehicle from getting pinned when the gate closes. A loop detector embedded in the pavement senses a vehicle sitting in the gate’s path and holds the gate open. Photo-eyes are the infrared beam that stops the gate if anything crosses the path while it’s moving. We installed both on every commercial slide gate we hang in Burlington, and we document their alignment in the photo record we leave with you. Call (928) 260-0864 if you want a written scope for your gate.
In Burlington, we dig post holes to 48 inches to get below Middlesex County’s approximate 4-foot frost depth. Gates installed with shallower footings, which is common on 1980s and 1990s residential installs, heave upward each spring when the ground thaws. The post tilts, the gate sags, and the latch stops lining up. There’s no shim or hinge adjustment that permanently fixes a post that isn’t below frost line. We reset the post at 48 inches, pour a footing with rebar, and document the depth with a photo before the concrete goes in. Call (928) 260-0864 for a written quote on the post work and the gate re-hang.
Written by Adrian Vance, Owner at Vance Gate Repair, serving Burlington since 2014.