Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Alpharetta
A new driveway gate in Alpharetta usually costs $2,800 to $7,500 installed, and most single swing gates run $2,800 to $4,200 depending on width, finish, and whether an automated operator is included. Double gates and slide gates land higher, typically $5,000 to $9,500, because they need two leaf panels, heavier posts, and often an HOA-approved operator. If you’re reading this from Windward, Crabapple, or anywhere along the GA-400 corridor, you already know the first question isn’t price. It’s whether your HOA will approve the design. We’ll walk you through that first.
Vance Gate Repair has handled Gate Installation in Alpharetta’s master-planned communities long enough to know the approval process matters as much as the dig. Call (928) 260-0864 and you’ll get a written scope and written price before any work starts, plus a documented photo record when we leave. That’s how we’ve done every job since 2014.
Why Vance Gate Repair Is Alpharetta’s Preferred Gate Installation Company
We’re the company Alpharetta HOAs call when a gate has to look right, work right, and pass architectural review on the first submission. Most of the installation jobs we take on here start with a copy of the community’s design guidelines in hand. We read them before we quote, so the gate height, finish, and operator model we propose already match what the architectural committee expects. That saves homeowners the expensive rework that comes from installing first and asking later.
Our technicians work in Alpharetta every week, from Windward to Kimball Bridge Road to the communities off Rucker Road. We know the brick-pillared entrances, the ornamental iron and aluminum finishes common in these neighborhoods, and the specific failure patterns of gate hardware installed during the 1990s and 2000s buildout. Adrian Vance, who founded the company out of commercial access-control work, applies the same documentation standards to every Alpharetta residential gate: wiring diagrams, limit-switch readings, and photographs of what was found and what was installed. You get that record when the job is done.
One thing you’ll notice about us: a live person answers the phone at (928) 260-0864 day or night. No voicemail queue. If a gate goes down before an HOA inspection or right before a holiday weekend, you reach a human who can dispatch a background-checked, uniformed technician to Alpharetta the same day.
Our Gate Installation Services in Alpharetta
Driveway Gate Installation
A driveway gate in Alpharetta is typically a swing or slide panel hung on brick pillars or ornamental posts at the bottom of a sloped or winding drive. We install both, but the site itself usually dictates which one works. A steep approach off Old Alabama Road or a short setback from the street often forces a slide gate, while a flatter frontage in a Windward cul-de-sac leaves room for a double swing. We survey the approach, measure the travel, check the grade, and write the recommendation down before quoting.
Pedestrian Gate Installation
Pedestrian gates in Alpharetta are usually the second gate on the property, sized for walkers and matched to the driveway gate in style and finish. HOA guidelines often require the pedestrian gate to read as part of the same design language, especially in communities where the entrance is visible from the street. We handle the fabrication match, the self-closing hinge spec, and the latch hardware so the gate passes inspection and still functions smoothly.
Sliding Gate Installation
Sliding gates work well on Alpharetta lots where the driveway angles or the frontage doesn’t allow a swing leaf to open fully without hitting the slope. The track and the concrete pad matter more than the panel itself. In this area, where red clay expands and contracts with wet and dry seasons, we pour deeper footings and set the track with the seasonal shift in mind. A slide gate that runs true today but binds in August or March wasn’t set for North Georgia soil. We set it for North Georgia soil.
Swing Gate Installation
Swing gates are the most common style we install in Alpharetta, usually paired with a high-end operator from FAAC, LiftMaster, or Elite. The critical point on any swing gate is the hinge post. In these post-1990 subdivisions, we regularly see gates sag not because the panel failed but because the pillar or post shifted in shrink-swell clay. Our installs address the below-grade work first: footing depth, post anchoring, and hinge alignment before the panel ever goes up.
Double Gate and Security Gate Installation
Double gates, which dominate the entrance to larger Alpharetta properties and HOA access points, require both leaves to meet flush at the center and latch without binding. Security gates add a second layer: they often integrate with telephone entry systems, RFID transponders, or a guard station. We install and program the gate and the access system as one job, so you’re not coordinating between two contractors and an HOA board.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterTrusted Brands We Service in Alpharetta
We install and service nine gate-automation brands, so whatever the hardware is on the pillars, we work with it rather than pushing a replacement. In Alpharetta we see a lot of LiftMaster, Elite, and FAAC operators on the high-end residential side, with BFT and Linear common on HOA entrances. We also carry parts for Ghost Controls and Viking for properties that already have those systems. We stock the parts Alpharetta customers need most frequently, which means a shorter wait when a board fails or a limit switch needs replacing. No steering you toward a new motor when a specific repair gets the gate running the same day.
Common Gate Installation Problems We See in Alpharetta Homes
- HOA architectural rejection after installation. A homeowner installs a gate that doesn’t match the community’s approved height, finish, or operator spec, and the committee orders it redone. We read the design guidelines first and submit the proposal before the first footing is poured.
- Swing gates sagging from post shift, not panel failure. North Georgia red clay expands when wet and shrinks when dry, and over a few seasonal cycles the hinge post drifts out of plumb. The panel was never the problem. The below-grade footing was.
- Slide gate tracks binding as brick pillars move. Alpharetta’s post-1990 brick-pillared entrances shift with the soil, and the track mount moves with the pillar. That causes rack and pinion wear and strains the operator until the track is reset and the motor re-tensioned.
- Access control integration gaps. In Alpharetta’s master-planned communities, a new gate often has to integrate with an existing telephone entry box, an HOA-managed credential database, or a resident RFID transponder system. A standard residential gate installer can’t always touch that side of the job. We can, because commercial access control is where our work started.
Pricing for Gate Installation in Alpharetta, GA
Here are honest ranges for Alpharetta’s market, based on the jobs we actually quote and install here. A single ornamental aluminum swing gate, manual or with a basic operator, runs $2,800 to $4,200 installed. A double swing gate on brick pillars typically lands between $5,000 and $7,800 including operator, safety photocells, and the post work. A slide gate with an automated operator runs $5,500 to $9,500, with the concrete track pad and footing work accounting for a meaningful share of that. If your community requires a specific finish, a custom width, or integration with an existing access control system, those items get their own line on the written quote so you see exactly where the dollars go.
The price we write on the estimate is the price on the invoice. You see it before we start, and you approve it before any work begins. We don’t hand you a verbal estimate and then surprise you at the end. Call (928) 260-0864 for a free, written estimate on your Alpharetta gate installation.
We Also Serve Cities Near Alpharetta
Our gate crews run through Alpharetta daily and reach the surrounding communities quickly: Roswell to the south, Duluth to the east, Woodstock and Canton to the northwest. If your property sits just outside the city line, the same HOA approval and red clay realities usually apply, and we handle those jobs the same way.
Serving Alpharetta, GA - Our Local Coverage Area
We’re based in the Alpharetta area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Alpharetta
Yes. Windward’s covenants require architectural committee approval for any new gate structure, and most of Alpharetta’s master-planned communities operate the same way. You’ll typically need to submit the gate style, height, finish, and operator detail before installation. We provide specification sheets and design drawings for your submission, and we coordinate the finish so it matches what the committee expects to see. Call (928) 260-0864 and we’ll help you assemble the approval packet before you spend a dollar on materials.
A loop detector, the sensor buried in the driveway that tells the operator when a vehicle is waiting, often fails or degrades on Alpharetta properties because years of red clay movement and moisture shift the saw-cut loop and break the wire. When we install a new gate and operator, we test the existing loops. If one reads weak or dead, it gets replaced during the installation rather than leaving you with a gate that won’t open for cars a month later.
Yes. Most of the gated communities in Alpharetta use a telephone entry system at the front gate, tied to a resident credential database and often an RFID transponder reader. We wire the new gate operator to that existing equipment and program the access controller so residents, delivery drivers, and management all work through the same entry flow the community already uses. This is the part of the job where our commercial access control background from 2014 forward makes a real difference.
If the footing isn’t designed for it, yes. North Georgia’s shrink-swell clay moves with wet and dry cycles, and a gate post set at a shallow depth will drift out of plumb within a few seasonal rotations. We over-excavate the footing, set posts deeper than the minimum, and use reinforcing that accounts for the soil’s movement. In Alpharetta’s post-1990 subdivisions where brick pillars already carry the hinges, we anchor into the structure and monitor how the pivot point reads before we hang the panel.
It’s a real consideration given what we saw across the Atlanta area in 2014 and again in 2021. Ice loads freeze slide gate tracks and force motors against resistance they weren’t designed to hold, and the strain takes out control boards. We spec operators for North Georgia conditions, which means proper torque settings, a battery backup where the HOA or homeowner wants it, and a track design that sheds ice rather than trapping it. A gate installed with these conditions in mind weathers the next freeze cycle far better than one spec’d for a milder climate.
If you’re planning a gate installation in Alpharetta, call (928) 260-0864 for a free written estimate. We’ll walk your property, check the soil and the pillars, tell you what the HOA needs to see, and hand you a price in writing before any work begins.
Written by Adrian Vance, Owner at Vance Gate Repair, serving Alpharetta gate installation and repair since 2014.